Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

41-608 no radio stations
#31

Methinks you need to replace the choke to supply the hv to the osc section. Let me see what I can find out abt it.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#32

Well the generally consensus is that it should be abt 3Mh. I have some 2.5Mh jobs but the current rating is much higher than what you need and physically they're fairly large. Can you take a pic of the one that's in there now?

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#33

Here is the choke and at the bottom of the tube is the resistor that should read 33000 but reads 46000.
#34

Well I can't get a photo to upload but the choke is about an inch long black with a green mark.
#35

I found a choke on Ebay that is  2.5mh RF Choke 0.17amp 24 ohm and about the same size. 4 of them for 25 dollars
#36

The choke arrived today. After replacing most of the resistors and installing the new choke I have full am reception including WSM Nashville! Just need a better antenna for better reception. Thanks for all the help with THIS radio. There will be more when I find them.
#37

Now to refinish the cabinet.
#38

Glad to hear you got it working , it's easy when you know how. Icon_angel You might want to wire in a 1amp fuse into the ac circuit for safety.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#39

Thanks for you help I don't think that I could have done this without your help. My aunt and uncle will really enjoy seeing it work again.




Users browsing this thread:
[-]
Recent Posts
The list of my radio & TV collection!
Yes, Michael. But strangely enough, I managed to keep the original veneer. I must admit that I don't really like it, so ...RadioSvit — 02:21 PM
The list of my radio & TV collection!
Good radio. I bet there was a lot of veneer fixing.morzh — 02:16 PM
Philco 46-480 Electronic Restoration
>> it is because I am retired and a little demented. You have just the right amount of it. No perfectly sane p...morzh — 02:14 PM
The list of my radio & TV collection!
Old Zenith 5S-29 tube radio. First turn-on after repair and reception quality testing. Demonstration of the operation of...RadioSvit — 01:27 PM
Philco 42-345 Restoration/Repair
Welcome to the Phorum, osanders0311!  Regardless how far you intend to restore this set, first priority should be replac...GarySP — 11:51 AM
Philco 46-480 Electronic Restoration
Joseph, it is because I am retired and a little demented. My problem is that I wanted to own a collection that spans th...MrFixr55 — 11:29 AM
Philco 46-480 Electronic Restoration
Wow, here I am with only two restored radios. I’ve got to boost those numbers! If you can’t run with the big dogs, you m...jrblasde — 10:04 AM
Philco 46-480 Electronic Restoration
Hello MrFixr55, That will for sure keep you out of trouble! Last Sunday was spent mostly doing yard work anyway the we...radiorich — 09:50 AM
Philco 46-480 Electronic Restoration
Throw in all the Audio equipment that has to be kept in a bedroom (my office)L. 8 portable self contained PA speakers, ...MrFixr55 — 07:40 AM
Philco 42-345 Restoration/Repair
Looking at the pic supplied by Rod B, you can duplicate the missing loop antenna. 10 gauge copper wire can be used to m...MrFixr55 — 01:20 AM

[-]
Who's Online
There are currently no members online.

>