Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

General Electric 202 revived.
#16

So it really only juices up signal going to output? Not really making it more sensitive? Paul

Tubetalk1
#17

It's still a solid little radio from GE and as far as I can tell, is at least a little more sensitive than my comparable five tube radios from the same time period. I get it about the styling as it is different. I wasn't really into this model either until someone here mentioned that they are good performers. Usually these are beat up or high priced around my area, but this one was a bargain flea market find this past summer. Icon_wink

No matter where you go, there you are.
#18

Just a guess on my part, but I'd guess that while the set is more sensitive than an AA5, it likely is not more selective. Have a look at the 1950 Philco model 50-921, for a very good sounding, super sensitive and selective bakelite table model that has tuned a RF and a tuned mixer for two tuned RF stages versus one stage in most sets. It probably won't be cheap either, but I have owned one and used it, and they are very good performers in a package about the same size as the G.E.
#19

want a sensitive and selective set then look for a howard a300 .
#20

I am sure that GE 202 is a very nice sounding and sensitive set. I just found it odd that they'd add the extra tuned stage up front and not tune a stage that was already there.
#21

John that Philco sounds like a nice set to have around i will keep my eye open.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently 2629 online users. [Complete List]
» 2 Member(s) | 2627 Guest(s)
AvatarAvatar

>