Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Radio Identification
#1

Hi all,
I am trying to find any info on this philco radio. I have trolled the I'net and the Philco gallery but no joy.
It has an Airzone 6DWS chassis ( I'm in Australia ) and am lead to believe that may have been made under licence here.
Any help greatly appreciated. Oh and is supposed to painted / lacquered dark in areas.
Cheers, Geoff.


Attached Files Image(s)
   
#2

Hi Geoff and welcome,
Unfortunately it doesn't seem to bear any resemblance to the US Philco sets. But the good news is that there are a couple of other forums to inquire with. I would try here   https://antiqueradios.com/forums/viewfor...c6ddc99c69  and  https://vintage-radio.net/forum/index.php

Best of luck with your project!

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Thanks for your help Roadioroslyn I will give them a try. Cheers.
#4

https://www.radiomuseum.org/dsp_treffer....rt=&Page=1

Try this site.

Jim
Spring Lake MI
#5

Thank all,
Will try those sites .




Users browsing this thread:
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM

[-]
Who's Online
There are currently 458 online users. [Complete List]
» 1 Member(s) | 457 Guest(s)
Avatar

>