Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Custom 1936 model 645
#1

Last year, a local friend was cleaning out their garage, and gave me a couple chassis. One is a 645 rescued from a crumbling 645 console.
I have no need for more consoles.  Icon_crazy
So I thought it might be a fun challenge to come up with and build my own tabletop tombstone. I like the shouldered tombstones.
I also like the grille cutout of the 650L.
So I cobbled these together in Photoshop.
Which do you all like best?
I recently saw a non Philco table top with the speaker on the bottom, and thought it was interesting. Hence the different design.
If I do move forward, it would drive some purists crazy, and possibly some historian crazy in 50 years.  Icon_lol

[Image: https://live.staticflickr.com/65535/5009...a75b_h.jpg]
[Image: https://live.staticflickr.com/65535/5009...db96_h.jpg]

Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
#2

Harp on top.
#3

From a practical point radio on the bottom speaker on top makes more sense. Easier to tune and see dial when it's placed on a table. But I think I like it the other way around (I'm lisdexsic).

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#4

Thought you were Italian. Icon_lol
#5

Speaker on top looks more appropriate to me.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.




Users browsing this thread:
[-]
Recent Posts
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM

[-]
Who's Online
There are currently 6960 online users. [Complete List]
» 2 Member(s) | 6958 Guest(s)
AvatarAvatar

>