Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

37-116 questions
#1

Is there a service bulletin noting the circuit differences between the model that uses the 6A5G vs the 6B4. Is that model distinguish by a code number other than 121 or 122?

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#2

Terry,

It says the changes are in Philco 8-3.
I haven't seen anything there specifically about 37-116.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

I know we had discussed it a little ways back when you got
your set.
Looked up the pin out and kinda interesting as the cathode is
internally connected filament at it's mid point. I would have
thought that it would have a separate pin with no relation to
the filament. Does your set have have a filament balancing
or hum adjusting pot?

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#4

Terry,

Don't want to misinform you, I do not remember. There might have been no trimpots in mine. Mine is 6A5 version.

Now that I think about it, probably there were no trimpots.

the two spare chassis' I have are 6B4 types. Probably same as yours.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#5

Terry

here.
https://philcoradio.com/phorum/showthrea...ght=37-116

My old thread.

Look at the comment #47 by JohnR.

This has both Service Bulletin # and the pot (#128) removed.
I guess it is a dual pot, as both pots have the same number.

Funny...in the mentioned SB #258 I found nothing about codes 125/126.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#6

Tnx Mike,
I thought that was the case but wanted to be sure.
There's a poster on arf that was asking abt the differences.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread:
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently no members online.

>