Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RCA 1R81 Update
#1

I thought I would share a better picture of my RCA 1R81 since I got it back today. The restoration on both this radio and my little Belmont 6D311 went very well, in fact my Belmont plays better than my buddy's now! Icon_lol 

   

The performance of this RCA is truly impressive and makes me wish at least one of my same year Zenith AM-FM radios would work. I have two of the big Zeniths from this same era with bad coils and the dreaded SMD! It seems like RCA must have finally got their act together with this series of AM-FM radios and Sarnoff must have finally decided that FM wasn't going away and they needed to catch up. They seem to have done well with this radio. I have had only two other earlier RCA AM-FM radios and one had bad IF cans (SMD!) while my 8R71 is an ok FM performer and still seems to be more an AM radio with FM tagged on. The 1R81 sounds good, doesn't drift and picks up channels very well. Only nitpick I have is that it uses an early version of a rod antenna for AM and it works TOO well! Picks up every bit of noise in the house between channels! Might have to try the AM out at the building later to make sure. It didn't do that at my buddy's shop, even with the lights. It does have a little bit of hum and the guy even put better electrolytics in it as he thought so too, even though all voltages check out. Using my little voltage reducer box brings it down to even more normal levels.

No matter where you go, there you are.




Users browsing this thread:
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently 2636 online users. [Complete List]
» 2 Member(s) | 2634 Guest(s)
AvatarAvatar

>