1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
46-1209 alignment
pdieten
Junior Member
**
Posts: 5
Threads: 1
Joined: Mar 2021
City: Milwaukee State, Province, Country: WI
#1

03-25-2021, 02:28 PM
Hi all 

Curating the radio collection and it's time to refresh the 46-1209 I last touched 10 years ago. Needed a good cleaning and the dial is wildly inaccurate. So I have the nine pages of Riders 15 for this radio and I intend to align it. Problem is, I can't find the index calibration marks on the dial backplate. Am I supposed to make my own calibration marks or something? 

And maybe it's the quality of my print but I'm also not 100% sure where all the trimmers C1, C6, C8, C12 and C14 are. 

Anyone have any ideas on what I should do about these? 

Thanks!
Paul
Find
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#2

03-25-2021, 09:46 PM
Have you seen the 46-1209 service bulletin in our library? https://philcoradio.com/library/download/service%20info/yearbooks/1946-1947/split/Part26-Philco%20Home%20Radio%20Yearbook%201946-1947.pdf

Its probably clearer than what you have.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
pdieten
Junior Member
**
Posts: 5
Threads: 1
Joined: Mar 2021
City: Milwaukee State, Province, Country: WI
#3

03-25-2021, 10:32 PM
That was exactly what I needed. Thank you very much. 

I think that I think it's silly that I have to make my own dial calibration marks, but it works.
Find
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#4

03-26-2021, 12:42 PM
Icon_thumbup
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM

[-]
Who's Online
There are currently 5952 online users. [Complete List]
» 1 Member(s) | 5951 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration