Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco clock radio
#1

Hello everyone,
Since I purchased a restored 1942 Philco last month, I've been trying to unearth information on clock radios from the 40s. My unit is Model 42-22-CL. I quickly discovered this model is "only" a radio with a clock. There are no mechanisms to automate the clock to set off alarms, etc. I'd be interested in hearing information from anyone knowledgeable about clock radios from the 1940s. Thanks very much!
#2

Welcome to the Phorum!
Icon_thumbup

I don't have any particular knowledge of 1940's clock radios but I do know that Philco had a clock timer that would turn a radio on or off in 1938. You can see my thread on the one I have at https://www.philcoradio.com/phorum/showt...?tid=13358 It was a separate unit from the radio. There is an article on a DIY "clock" radio from Popular Mechanics in 1940 found on OneTubeRadio.com.

There is just a bit of info in the Philco Gallery about your model if you have not yet seen it. https://philcoradio.com/gallery2/1942a/#Model_42-22CL
#3

It's a great looking clock/radio regardless! Take care and BE HEALTHY! Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#4

One other thought, the clock mechanism in the radio timer I restored was a Telechron if I remember correctly. I suspect many of the clocks put into radios at that time might have been Telechron. Here's a website with some info: https://telechron.net/main.htm
#5

My very limited experience with clock radios being GE, RCA, TRAVLER all used a Telechron clock the sets were AA5 or AA6.
#6

The 1940, 1941, and 1942 Philco models which had clocks used Sessions movements.

The first Philco radio to include an alarm clock was model 50-527, a 1950 model. Philco may have been using Telechron movements by this time, since the 50-527 clock looks like the same basic clock (other than the clock face) used by other radio manufacturers.

--
Ron Ramirez
Ferdinand IN




Users browsing this thread:
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 4302 online users. [Complete List]
» 1 Member(s) | 4301 Guest(s)
Avatar

>