Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Alkaline or Heavy Duty batteries in our old portable radios?
#1

I've been on a vintage solid state kick again and have been tinkering with my old Zeniths from that era. I dug out my rebuilt Royal 2000 and realized the old sets of alkaline batteries I have been using are no longer trustworthy, so I bought two six packs of heavy duty Rayovac D cells at Big Lots for a little over $10 with the tax included. My realization is that this radio and others I have were made before alkaline batteries were even a thing and will work just as well with the cheaper carbon type. I have four batteries left over and another pack will allow me to get my Royal 3000 up and going as well. Might be interesting to see how long these batteries will last in the rebuilt Zeniths compared to the alkaline D cells. $10.65 for 12 batteries is a lot cheaper than even the store brand alkaline batteries in my area and there might be stores with the Heavy Duty even cheaper yet. Shopping around right now in my area is almost dangerous with constantly angry and careless drivers. So, now to make my Royal 2000 my Christmas radio!

No matter where you go, there you are.
#2

Doesn’t really matter what type even quality. What matters is forgetting that batteries have been left inside and the potential for leakage.

On older radios, often, there is a bypass capacitor across the battery at all times. If this capacitor is electrically leaking the battery will be slowly discharged inviting chemical leakages. This can be avoided by checking for this “phantom” current flow and correcting it.

Chas

Pliny the younger
“nihil novum nihil varium nihil quod non semel spectasse sufficiat”
#3

Never leave a battery in a radio! When you turn it off take them out. I am not happy with the way any batteries are being made at this time, brand name or store name most are JUNK! Sorry about the rant have purchased batteries and had them start leaking in a few weeks and still in the new packing.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM
40-150 General questions
I discovered a stamp on the underside of the breadboard on my Philco 40-150. It is"56-1417' in black ink with numbe...Kevin_D — 07:14 AM
Philco 38-7 Speaker
FYI the Impedance of the HR20 (the one I have) secondary of the audio transformer is 5 ohms. The 38-7XX speaker is suppo...tludka — 04:22 PM
Philco 38-7 Speaker
Yeah, don't use the transformer currently on the H-20 (Dopf, I thought "H20, is that new technology, a speaker usin...MrFixr55 — 03:51 PM

[-]
Who's Online
There are currently 2769 online users. [Complete List]
» 2 Member(s) | 2767 Guest(s)
AvatarAvatar

>