Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Model 76 Highboy
#1

Back in Feb I scored a nice model 95 Highboy, see earlier post.  Saved from a guy that likes chopping them up into Liquor cabinets.  Icon_thumbdown Icon_thumbdown   Yesterday I found its brother, a model 76 Highboy.  Same cabinet, different chassis inside.  I believe there was four different radios you could get in this cabinet back in 1929.  As with the model 95, this one is in great shape original finish with a tapestry cloth in fantastic shape.  This one has a bit of veneer peal on the bottom of both sides, but not too bad and easily fixed.  Could not pass it up for only $40. Bonus, this one still had a good RCA UX245 in it.  Icon_thumbup Icon_thumbup   Issue is, I don't have room for all of these consols.  Plan to get them both running and then will have to let one go.


Attached Files Image(s)
                           

Philco's 
86 Low Boy     71B      42-321T
90 High Boy    52B      46-1203
95 High Boy    118B     48-214     
112X Console     60B       48-206
118X Console     84B       49-506
41-608P Console   610B   76 High Boy
41-265 Console   37-89B   370LZ
52GC                38-35B
20 Baby Grand   38-10T
70 Baby Grand   41-221CI

#2

That's a nice looking cabinet. With a little bit of rub on stain and paste wax that should even out the finish. When you replace the filter caps on this set it's important to use film cap rather than ecaps. They're low values like 1 or 2 mf @630v.  Primaries on the rf coils a lot of times are open, not a big deal to rewind. 

Have fun chasing electrons!

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Looking for verification of correct schematic.
Definitely 870044RossH — 01:12 PM
12' Philco
Wonder if the chassis was big too.daveone23 — 12:38 PM
Philco 38-2 Automatic Tuning
Hi Ron, I have sent Radio Daze my concerns with the dial so I guess we will see. They used my original to make the repro...dconant — 12:27 PM
Hickok AC51 tube tester
How does the  5W4 and 83 tube filaments get fed?martinj — 12:25 PM
462ron
Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM
Philco 38-2 Automatic Tuning
I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM
Philco 38-2 Low Volume
I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM
Philco Speaker Spider
Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM
Philco 16B Parts
Hello, I'm looking to buy a 16B but I'm not so sure of what I am looking at. First as seen from the picture it looks lik...dconant — 09:17 AM
Looking for verification of correct schematic.
Klondike98, Thank you. I'll double check that SN and get back to you. GarySP, Thank you for the schematic.RossH — 12:13 AM

[-]
Who's Online
There are currently 1278 online users. [Complete List]
» 1 Member(s) | 1277 Guest(s)
Avatar

>