Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Another Philco 44 variant?
#1

Ron and friends,

Here's a Philco model 44 highboy that I'm repairing for someone. This has a cabinet like some other models (43, 47, others) from 1933. However, you don't have a model 44 in this cabinet in the Gallery.

[Image: http://antiqueradios.com/gallery/d/12560..._front.jpg]

[Image: http://antiqueradios.com/gallery/d/12560...4_back.jpg]

Here's the chassis label:

[Image: http://antiqueradios.com/gallery/d/12561..._label.jpg]

There is also a label on the inside of the cabinet wall indicating model 44.

Is this a new one to add to the list of model 44 variants?

Tom
#2

Hi Tom

I would say so.

It is apparent that Philco's Furniture History records are incomplete, as this is not the only Philco cabinet from that time period (1932-34) that is not documented. I just checked Philco Furniture History again, and no, this 44 is not mentioned.

Would you please send me a larger (higher resolution) photo of that 44 so that I may add it to the Gallery? Thanks in advance.

mr.philco AT yahoo DOT com

BTW - very clean radio! You don't often see sets this nice.

--
Ron Ramirez
Ferdinand IN
#3

I'll send you some pictures now. The radio is very clean, and that's the original finish. One of the best original finishes I've seen on a radio that old.

Would you think it likely that this cabinet style came after the 44 highboy you've got in the gallery? Looking at Philco highboy cabinet trends, this somewhat less ornate style looks to me like it may have been a later version, but I certainly can't say for sure.
#4

Pictures received, and photo posted in the Gallery (Fall 1933 page). Thanks, Tom! Icon_smile

It's hard to say whether your 44H was issued before or after the 44H which was already shown in the Gallery. Like you, I would tend to believe it came later, but I cannot say for sure since it is not documented.

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5096 online users. [Complete List]
» 2 Member(s) | 5094 Guest(s)
AvatarAvatar

>