Posts: 19
Threads: 3
Joined: Dec 2010
City: Tampa, FL
I was given this old Philco cathedral radio and am trying to find out the model and year it was made if possible. There are no markings on the chassis or wooden case that I can see. I hope the pics will tell the story.
I'm sure you guys know...right?
Note from site admin: Sorry, but the photos which were attached to this post are no longer available.
Best regards,
Kico
"I whisper, but my horse still doesn't listen."
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Hello, and welcome!
You have a Model 84B, the late version from January 1936:
http://www.philcoradio.com/gallery/1936b.htm#c
That is an oversized power transformer. Might be a 25 cycle model? If so, it will work on today's 60 cycle line current.
--
Ron Ramirez
Ferdinand IN
Posts: 19
Threads: 3
Joined: Dec 2010
City: Tampa, FL
Thanks Ron,
I tested all the tubes and they all check good. I then fired it up on my dim bulb tester...as expected a very loud 60 cycle hum but no smoke ![Icon_smile Icon_smile](https://philcoradio.com/phorum/images/smilies/icon_smile.gif) ...faulty power supply cap I suspect.
Any good links here on the forum for rebuilding one of these?
Thanks again...
Best regards,
Kico
"I whisper, but my horse still doesn't listen."
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
You may want to search this site for similar models like model 80,84,600, 57,37-84.
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 19
Threads: 3
Joined: Dec 2010
City: Tampa, FL
7estatdef Wrote:You may want to search this site for similar models like model 80,84,600, 57,37-84.
Terry
Thanks Terry,
Whew...there's a lot here. I was wondering if anybody has compiled a component list (caps/resistors, etc.) needed for rebuilding an 84B they could post or send me? My eyes are not what they used to be, and reading the actual and schematic values is difficult. I'd like make sure I have the correct parts before I place an order.
Also, could someone on the forum link me to the correct schematic for this radio...thanks.
Best regards,
Kico
"I whisper, but my horse still doesn't listen."
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
May I suggest you contact Chuck Schwark to obtain the service information package for this radio, which will include an 11 x 17 enlarged schematic, parts list, alignment info, changes, etc., etc.
http://www.philcorepairbench.com/schematics.htm
Well worth the nominal fee.
--
Ron Ramirez
Ferdinand IN
Posts: 19
Threads: 3
Joined: Dec 2010
City: Tampa, FL
Thanks Ron...I'll do it!
Best regards,
Kico
"I whisper, but my horse still doesn't listen."
Posts: 270
Threads: 12
Joined: Nov 2005
City: Nashville, TN
Hi Ron,
I am working on one of these right now, the exact same cabinet. But the inside label says it's just a model 84. Does the 84B just refer to the style of cabinet, and is not marked so on the blue tag?
I do have another 84 but with the more circular cabinet.
Kico, I posted some photos an info for you on your other thread.
Thanks. Gary.
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Hi Gary
Yes, the "B" referred to the style of cabinet; in this case, "B" = Baby Grand - which is how Philco referred to its cathedrals and tombstones back then. The terms "cathedral" and "tombstone" did not come into general use until decades later, as people like us began to collect these radios.
The sticker on the back of the chassis will read "CHASSIS TYPE 84" without mentioning the cabinet style.
--
Ron Ramirez
Ferdinand IN
Posts: 270
Threads: 12
Joined: Nov 2005
City: Nashville, TN
Thanks Ron, that clears up the mystery.
Working on the cabinet today, shouldn't be too bad. No veneer or photofinish to worry about.
Take care,
Gary
Users browsing this thread:
|
Recent Posts
|
Cannot Adjust an IF Transformer’s cores
|
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM |
Cannot Adjust an IF Transformer’s cores
|
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM |
PT-6 antenna connections
|
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM |
Cannot Adjust an IF Transformer’s cores
|
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM |
PT-6 antenna connections
|
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4.
Yes, pin 6 of the 7C6 is...RodB — 07:34 PM |
bridkarl
|
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM |
Cannot Adjust an IF Transformer’s cores
|
Joseph, now you are an engineer!!RodB — 06:37 PM |
PT-6 antenna connections
|
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM |
Cannot Adjust an IF Transformer’s cores
|
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM |
PT-6 antenna connections
|
I seem to have lost my way on this PT-6.
I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM |
Who's Online
|
There are currently no members online. |
|
![>](https://philcoradio.com/phorum/images/bootbb/asb/right_arrow.png)
|