Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

philco model 60 help needed
#1

I need some help.

1. Someone connected a 0.047 cap from the tone control to the 42 tube. What is the purpose of this and is it needed. The schematic does not show anything there but there is a wire from the tone control.

2. The wave band selector is missing a connection from the brown black resistor. Where should this wire go?

3. I would like clarification of where all the filter condenser bank caps go and the best place to ground them.

I have rebuilt all the bakelite blocks and I am stuck on the above three questions. Hopefully I did everything else right Icon_rolleyes Someone really hacked this one. Icon_sad I have the schematic but have a hard time following it.

I can't wait to hook it up to the variac and give it a try once I get over the stumbling blocks.

thanks
Chris
#2

Hi Chris

I can help you on some of this...

1. No, the extra .047 uF cap should not be in the tone control circuit, and should be removed. There are two capacitors inside the tone control - .01 & .015 uF. These are the only caps in the tone control circuit, and should be replaced if you have not done so already.

2. You must mean resistor (1), 10K, which connects across two terminals of the band switch, with wires from each end of the resistor also going to the antenna coil.

3. Sounds like you need a photograph of a known good, or properly wired, Model 60 chassis. Unfortunately I am not in a position right now to furnish such a photo (I have a Model 60 chassis, but it is not here with me).

Bear in mind also that there were a lot of changes made to the Model 60 chassis over its three-year production run. So much so that I posted an "Evolution of the Model 60" page on my website.

http://www.philcoradio.com/tech/60evol.htm

--
Ron Ramirez
Ferdinand IN
#3

Ron,
If you do have a chassis and have the time, a picture would really help me. Did you get my e-mail on the 84 trade?
thanks
Chris
#4

Chris - received, and replied. Icon_smile

It may be awhile before I can get a picture of a 60 chassis to you, but I shall do so as soon as I possibly can.

--
Ron Ramirez
Ferdinand IN
#5

Hi Chris,
These may help.......... or may not.......... I dont remember what version 60 this is (its not my set), but it is a 60 Icon_biggrin .

[Image: http://i9.photobucket.com/albums/a77/1ph...assis8.jpg]

[Image: http://i9.photobucket.com/albums/a77/1ph...assis2.jpg]




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently no members online.

>