1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
42-1008 speaker/turn table question
Guest
Unregistered
 
#1

11-22-2006, 10:17 PM
I would like to replace the speaker with something new. What should I choose? I am also thinking of removing the turn table and installing a modern one - should I? If not, where can I find a new needle?
Guest
Unregistered
 
#2

11-22-2006, 10:32 PM
How about the Cerwin Vega 12" dual-voice?
Chuck Schwark
Phorum Expert
*****
Posts: 1,703
Threads: 55
Joined: Sep 2005
City: Evanston, IL
#3

11-23-2006, 11:06 AM
A modern 12-inch PM speaker will NOT work in this set without some power supply modifications. The original speaker (part no. 36-1528 ) is an electrodynamic type and the filed coil is also the filter choke in the power supply. The field coil D.C. resistance is 1,000 ohms and the voice coil impedance is 5.1 ohms.

Try Play Things of Past (http://www.oldradioparts.com) for a possible replacement speaker or a junker set on ebay. Same speaker is also used in the 42-1009. A compatible speaker (part no. 36-15224 or 36-1565) was also used in Models 42-1012, 1013, but with a slightly lower field coil resistance of 860 ohms. A suitable power resistor could be added in series with it to compensate.
Chuck Schwark,
The Philco Repair Bench
[Image: http://www.philcorepairbench.com/images/philog3tiny.gif]
http://www.philcorepairbench.com
Website Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread:
[-]
Recent Posts
Refinishing Ideas
Hi Poulsbobl, I think that you could get away with it.  In the Philco Library, there is a parts listand specs for sp...MrFixr55 — 11:54 PM
Philco 46-480 Electronic Restoration
The sleeving for the transformer arrived early, so I went ahead and finished reassembling. The chassis looks far better ...jrblasde — 10:15 PM
Philco 610B oscillator wiring
I don't know what you are referring to when you say "tube cathode ground". Ground is a connection to the chass...RodB — 05:56 PM
Zenith H725
Good points, Arran. I haven't encountered this problem with any other radio (all earlier vintages), so am learning here....EdHolland — 05:32 PM
Zenith H725
Ed; One thing that I will say about these is that Brand Z was considerate enough to make these mica caps easily acces...Arran — 02:34 PM
Philco 610B oscillator wiring
Do you know what run # your chassis is? It took me a while to find what you were basing updates/modification on as I did...Radioroslyn — 07:34 AM
Need to purchase some accessories for restoration of my Old Philco Radio
COLLEAGUES, Thank you all for such good and important suggestions as how to find good replacement parts. I will go fo...palonso — 07:05 AM
Zenith H725
Here's what the inside of AM IFT2 looked like, and the other pic shows the discs I made to take place of the mica and ke...EdHolland — 07:40 PM
Zenith H725
IF2 will need replacement caps. The arcing was severe enough that the mica is pitted and holed where the HT flashed over...EdHolland — 04:04 PM
My Philco 37-116 Restore
Measuring from center tap like the tube voltages show. Cap 127 is isolated from ground. Cap 127 shown in upper left of p...dconant — 08:05 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration