Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

My New Phil(co)-Silver set :) :)
#1

I got the cabinet shown below on ebay today. It is/was a 38-116 that was cut short and had a maple top board added. Currently it houses a 12" Jensen SG220 speaker, what ever that is.

Concurrently, I have had a fellow up in Wisconsin restoring my McMurdo Silver Masterpiece 2 set, which is a 2 chassis 12 tube set circa 1933 or so. It uses 2-2B6 output tubes, making it a late model version. The chrome on the main chassis and its cover box are stunning and it was really made by the Hallicrafter company with a dual dial arrangement. I think the left side dial is a fine tuner. The main chassis will sit proudly on top of this cabinet. I have been wondering if the Philco clarifiers would work too if added in this combo.

Anyway, my guy last week was able to get the MP 2 working and told me it a really HOT player too. Thanks to Norman Braithwaite for supplying the missing schematics to pull it off too.

The plan is for the Phil-Silver to go into my McMurdo room (aka my living room) where it will get played in rotation with the others in the room. I play a different set each day and the spot I have picked out currently has a very nice Scott I got from forum member Mike via Ron Ramirez's referral.

The 38-116 cabinet is very large but so is the reserved parking spot for it.
I will have to modify the cabinet by adding a lower shelf for the amp
and mounting of the 12" Jensen pedistal speaker but should not be too difficult. Note even the pedistal stand on the speaker is chromed too.

I also need some V chevron grill cloth or something similar to make it more Philco-ish too.

[Image: http://i.ebayimg.com/t/VINTAGE-JENSEN-SG...~~60_3.JPG]
[Image: http://i213.photobucket.com/albums/cc249...riZQ_3.jpg]
[Image: http://i213.photobucket.com/albums/cc249...ZsjQ_3.jpg]
[Image: http://i213.photobucket.com/albums/cc249...4CFQ_3.jpg]
[Image: http://i213.photobucket.com/albums/cc249...qtMw_3.jpg]
[Image: http://i213.photobucket.com/albums/cc249...Ow9Z_3.jpg]
#2

WOW! A guy needs welder's dark tinted goggles to look at the radios you have, Bruce! 8)

Mike
#3

Snazzy!
#4

Two thumbs up! Icon_thumbup Icon_thumbup

Congratulations, Bruce!

--
Ron Ramirez
Ferdinand IN
#5

Wow, that's swell!

And in my opinion an accurate example of one way they would have come up with an acceptable "cabinet" for the Silver.
#6

That speaker looks similar to the one that came with the EH Scott AW12 I got back in May, except it has the Scott decal on the back, of course. It's more similar to that than to the speaker I had with the AW15. I assume then that my speaker is a Jensen.

Mike




Users browsing this thread:
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently 3940 online users. [Complete List]
» 1 Member(s) | 3939 Guest(s)
Avatar

>