Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philcos from New Zealand and Peru
#1

The AM only Philco 401 is from New Zealand, and the multiband Philco is from Peru (at least that's where I got it from via ebay).

I could use a schematic for the 401 if anyone has one, thanks.


Attached Files Image(s)
   
#2

The New Zealand set looks like an Australian made Philco from the 1950s, note that it uses the same cabinet as a U.S/Canada Transitone model but with a glass dial. The set from Peru looks a lot like a member of the Philco Tropic series, which was an export model, it may have been assembled in Peru but it looks like it's patterned from a Tropic with the two short wave bands.
Regards
Arran
#3

Here's my 46-806:

[Image: http://www.philcoradio.com/gallery/image.../46806.jpg]

http://www.philcoradio.com/gallery/1946a.htm#q

Yep, it is a member of the Tropic series, most of which were made in Philadelphia and then exported, mostly to South America but to other countries as well. I've received emails from folks in places like South Africa and northern Europe who have Tropic sets.

It appears that sometime in the 1950s, Philco Tropic production switched to Philco's UK subsidiary. I have two UK-built Tropics; one was purchased from a USA seller but I had the other one sent here from England; the radio was very cheap but the shipping wasn't! Icon_eek

--
Ron Ramirez
Ferdinand IN
#4

Ron;
Didn't they produce a number of Tropic models in Canada as well, I remember that you posted some pictures of an early 50's example with a broken cabinet, with a hot chassis, and it was made in Canada. There is a 1950s era Philco Tropic about three hours South of me but the party selling it wants $65 for it, they claim that it was from the Caribbean in the ad. I thought about asking about it but it's still just a plastic/Bakelite set for too much money.
Regards
Arran
#5

Yes, you're right, Arran. That early 1950s Tropic I have - a model 3010 - is rubber-stamped on the back of the chassis MADE IN CANADA. And, yes, it is a hot chassis. Icon_eek I bought a 51-532 just for the cabinet, to replace the broken but otherwise identical 3010 cabinet.

The Tropic you mention for sale was, I am sure, exported to the Caribbean when it was new but it was most likely not manufactured there.

Speaking of Canadian sets, there are a few Philcos that were made and sold in Canada that are identical to Tropic sets built in the USA and exported south. Sets such as the 35AT (41-712T), 39AT (41-722T), and the 55AT (42-760T). In fact I have a 39AT, I consider it part of my Tropic collection since it is identical to the 41-722T. I used to own a 55AT but later sold it.

--
Ron Ramirez
Ferdinand IN
#6

Ron;
On the 46-806 Tropic model that you show where is the range switch located? I see two knobs on the front like a normal Transitone with the same cabinet but no third one, on most small sets like that they would have drilled a third hole in the front and added the range switch there.
Regards
Arran
#7

They put the band selector switch on the back of the radio. Mounted to the back side of the chassis. Philco must have expected that few users of this set would change bands all that often...




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Refinishing Ideas
Hi Poulsbobl, I think that you could get away with it.  In the Philco Library, there is a parts listand specs for sp...MrFixr55 — 11:54 PM
Philco 46-480 Electronic Restoration
The sleeving for the transformer arrived early, so I went ahead and finished reassembling. The chassis looks far better ...jrblasde — 10:15 PM
Philco 610B oscillator wiring
I don't know what you are referring to when you say "tube cathode ground". Ground is a connection to the chass...RodB — 05:56 PM
Zenith H725
Good points, Arran. I haven't encountered this problem with any other radio (all earlier vintages), so am learning here....EdHolland — 05:32 PM
Zenith H725
Ed; One thing that I will say about these is that Brand Z was considerate enough to make these mica caps easily acces...Arran — 02:34 PM
Philco 610B oscillator wiring
Do you know what run # your chassis is? It took me a while to find what you were basing updates/modification on as I did...Radioroslyn — 07:34 AM
Need to purchase some accessories for restoration of my Old Philco Radio
COLLEAGUES, Thank you all for such good and important suggestions as how to find good replacement parts. I will go fo...palonso — 07:05 AM
Zenith H725
Here's what the inside of AM IFT2 looked like, and the other pic shows the discs I made to take place of the mica and ke...EdHolland — 07:40 PM
Zenith H725
IF2 will need replacement caps. The arcing was severe enough that the mica is pitted and holed where the HT flashed over...EdHolland — 04:04 PM
My Philco 37-116 Restore
Measuring from center tap like the tube voltages show. Cap 127 is isolated from ground. Cap 127 shown in upper left of p...dconant — 08:05 AM

[-]
Who's Online
There are currently no members online.

>