Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Not sure what i have...HELP??
#1

Can someone tell me how to find out info about a set i have...it is a philco console, but i can't find a pic like it on here. the face of the radio is on the upper front, has wooden buttons for selction, but also has 4 large dials on either side of the face. Has several different countries listed on the face/...along with AM and aircraft and several more..don't remember the others and i am not where it is at the moment...if someone could point me in the right direction i would be most thankful

Deb (sorry don't have a pic at the moment)
#2

Hi Deb and Welcome to the Phourm!!!
Without a pic it going to be tough! You maybe able to find a small blue and white sticker on the inside of the cabinet that will display the model number. It may also be stamped in ink on the chassis. Most of the time it will be two digits a dash and one-three more digits. The first two will be the year it was made. Did you have a look in the Gallery??
Terry
#3

Thanks Terry, i kept looking thru the gallery and think i found one that is pretty close...It looks like the 40-215RX only the buttons are closer together and are wooden
#4

Philco never used wood push buttons. They where tenite which is an early type of plastic. Not known for it's longevity most have badly deteriorated by now. Replacements are available. Maybe someone hand carved wooden replacements?
Terry
#5

Hello, Deb: try to get a pic to post here on the Phorum, that would be a major help in pin-pointing what you have.
#6

She figured out at it's a 41-295. Now she try to find it's worth. I gave a few ideas...
Terry
#7

Zehr gut!!!




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently no members online.

>