Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

General Electric models A-205 & A-208
#1

    Are there any of these 20-tube monsters about?

One seldom sees the larger sets from GE. The 208 was the phonograph job.

Touted as a "True Fidelity All-Wave Radio", they had 6 (yes, 6) 6F6's in PPP output.

BTW, if anyone needs info, I have the factory service manual set covering all GE radios from 1930 to 1939.

Dennis

Pacing the cage...
#2

Just when you think that you've seen them all.....

I had to research that one, as I had never heard of or seen one before.

From the description it sounds like a monster.
#3

This model had rated 40 Watt output delivered to two 11" speakers.

It also used a unique switching arrangement to allow defeat of the superhet function and go to a TRF circuit (only on broadcast band), for ultimate wideband performance.

I have never seen any other radio of the age use this design.

The slightly later "A-205/8E" model was bi-amped, with 10 more watts for just the tweeters.

It probably gave the Strat and Masterpiece a run for their money in terms of sound.

Dennis

Pacing the cage...
#4

I have noticed that what you find or do not find in a given area largely depends on what dealer network was in your region when the set was made. In my area there was a regional distributor for Canadian General Electric and another for Philco, and there was a DeForest Crosley, an RCA, a Canadian Westinghouse, and a Sparton dealer in the area, so I see a fair number of those. I would bet that you would be more likely to see one of those big G.E sets in the New York/New England area or at least in an area that had a large G.E distributor nearby. I have seen some larger G.E sets but they are Canadian G.E sets, an altogether different animal.
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions.  I'll write to the Henry Ford.   That would certainly make sense since by the time this prod...jeibner — 11:49 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option. The obvious ...GarySP — 11:39 AM
Help with Readrite 410 tube tester
Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
We have a regional museum here in the Twin Cities called The Pavek Museum. They have an extensive collection of communic...RodB — 09:30 AM
Philco 89B code 123 newbie
I did some nosing around and found that the original caps were 4 3/4" long x 1 5/16" in dia. Guess what 1"...Radioroslyn — 09:28 AM

[-]
Who's Online
There are currently no members online.

>