1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 48-1264
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#1

01-23-2022, 04:14 PM
Any one know where you hook up the Fm antenna to this?

Skip
Find
Mondial
Phorum Expert
*****
Posts: 1,114
Threads: 14
Joined: Feb 2013
City: Irvington, NY
#2

01-23-2022, 04:23 PM
There is a little 4 pin socket on top of the RF front end chassis, between the AM antenna terminal strip and the 6BA6 IF tube. The schematic shows the pin connections for the mating plug of the in cabinet FM dipole.

https://philcoradio.com/library/download...8-1949.pdf
(This post was last modified: 01-23-2022, 04:24 PM by Mondial.)
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#3

01-23-2022, 05:36 PM
ok thanks hooked up antenna FM completely dead no noise or signals. AM works fine.

So either doing something wrong? or FM is bad.. Not sure what to check next.

Skip
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#4

01-23-2022, 10:43 PM
ok started to go thru alignment procedure for Fm

Fm alignment steps 1 and 2. heard the 9.1 mhz signal.. did not adjust anything yet...had to use a strong signal. -3.5 dbm modulated.

went to next step sig generator to pin 4 j400 frequency of 105 mhz no signal heard at all..

Skip
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#5

01-24-2022, 08:41 PM
OK Found problem... The 7F8 converter tube was loose in socket moved it around and FM started working.

So now onto alignment

Skip
Find
« Next Oldest | Next Newest »




Users browsing this thread:
[-]
Recent Posts
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM
Philco Predicta Siesta picture over time getting dimmer
I found that the wire insulation was burnt.  The fly back needs corona dope! Why would someone put that there?Platinumblonde36 — 01:09 AM

[-]
Who's Online
There are currently 5168 online users. [Complete List]
» 1 Member(s) | 5167 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration