1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Model Philco 37-10 Year & Light Bulbs
SoCal-Poor-Boy
Unregistered
 
#1

03-26-2013, 09:55 AM

What year is my Model 37-10 Stand up Philco Radio.
Also where can I get the G-E 47 Bulbs. Need 5 or 6 Can't remember. Found Tubes OK From Antique Electronic Supply @ 480-820-5411
Thanks Ron AKA SoCal-Poor-Boy. Mis CA. MN. is Cold and 50% Higher Cost of Living than CA??? . Icon_wave
OH Pic. of other Baby...


Attached Files Image(s)
   
Art Hoch
Senior Member
****
Posts: 403
Threads: 40
Joined: Feb 2011
City: McPherson, KS
#2

03-26-2013, 12:33 PM
Well your 37-10 is a 1937 model. I assume the 47 you refer to is a dial lamp?! Should be able to find them the same place you found tubes--AES. Other suppliers have them too.
Find
klondike98
Phorum Moderator
******
Posts: 5,060
Threads: 269
Joined: Nov 2012
City: Bandon State, Province, Country: OR
#3

03-26-2013, 01:41 PM
http://www.tubesandmore.com/products/P-47 or http://www.radiodaze.com/category/60.aspx or others.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »




Users browsing this thread:
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 4016 online users. [Complete List]
» 3 Member(s) | 4013 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios