Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

41-608 bol
#1

hey guys
i purchased 2 sales listed as philco speakers 1 was a steal other inflated by seller but still cheep.
question is i belive they are mic`s as i have seen them before . 1 has a wire that goes to black box at top in rear of cabnet i opened it up looks like speaker to me ??


Attached Files Image(s)
   
#2

I bet it is intended as a mic but is just a small speaker. The low Z is boosted by the box which is an input transformer.
#3

Almost all passive electrical machinery is reciprocal.
#4

Yes. I seem to recall (in the dark, distant past), during "experiments", I was able to use a speaker as kind of a microphone. Icon_crazy Odd, but semi-effective. Icon_wtf Could be a hybrid?
#5

Dunno about that, but a small PM speaker makes a very good microphone, just use an output transformer in reverse. Done all the times in old time intercoms. In fact they sometimes used 45 ohm PM speakers to minimize losses in wiring from remotes to masters. Dunno about modern ones though.
#6

thanks guys
i only seen one with the radio for sale but was way to expencive for me
i see them on ebay but no cords as this one has cord i see where it goes .it dosen`t say any about it on my schamtic`s
now all i need is plater to motor cupler and it is complete
amazing a speaker can be a mic too!!
sam




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 46-480 Electronic Restoration
After sleeping on it, I believe the issue is that I may have forgotten to install a ground connection between the RF cha...jrblasde — 09:21 AM
Refinishing Ideas
Hi Poulsbobl, I think that you could get away with it.  In the Philco Library, there is a parts listand specs for sp...MrFixr55 — 11:54 PM
Philco 46-480 Electronic Restoration
The sleeving for the transformer arrived early, so I went ahead and finished reassembling. The chassis looks far better ...jrblasde — 10:15 PM
Philco 610B oscillator wiring
I don't know what you are referring to when you say "tube cathode ground". Ground is a connection to the chass...RodB — 05:56 PM
Zenith H725
Good points, Arran. I haven't encountered this problem with any other radio (all earlier vintages), so am learning here....EdHolland — 05:32 PM
Zenith H725
Ed; One thing that I will say about these is that Brand Z was considerate enough to make these mica caps easily acces...Arran — 02:34 PM
Philco 610B oscillator wiring
Do you know what run # your chassis is? It took me a while to find what you were basing updates/modification on as I did...Radioroslyn — 07:34 AM
Need to purchase some accessories for restoration of my Old Philco Radio
COLLEAGUES, Thank you all for such good and important suggestions as how to find good replacement parts. I will go fo...palonso — 07:05 AM
Zenith H725
Here's what the inside of AM IFT2 looked like, and the other pic shows the discs I made to take place of the mica and ke...EdHolland — 07:40 PM
Zenith H725
IF2 will need replacement caps. The arcing was severe enough that the mica is pitted and holed where the HT flashed over...EdHolland — 04:04 PM

[-]
Who's Online
There are currently 820 online users. [Complete List]
» 3 Member(s) | 817 Guest(s)
AvatarAvatarAvatar

>