Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 38-3 Volume Control
#1

I had my model 38-3 radio recapped recently. It plays very well but it seems that there is an issue with the volume control. When I turn the volume control fully counter clockwise to the minimum volume setting the radio does not mute. A few times when I turn the volume clockwise to increase the volume the volume will increase but most of the time the volume actually decreases a bit. This does seem to be intermittent but again most of the time the volume control doesn't adjust the volume level. It seems to remain at a constant level. What should I check to see if I can correct the volume control?

Thanks,

Charlie
#2

Looks like a tapped volume control, might be hard but not impossible to find a direct replacement. I'd try cleaning it with some deoxit, and measuring end to end and with wiper moving resistance with ohm meter, tap included. Work arounds with still obtainable controls can be done.

If the paper capacitors and ancient carbon resistors have been replaced, these should not be an issue.

Let us know.

Kind of blurry schematic here:
No cost version:

http://www.nostalgiaair.org/PagesByModel...013243.pdf

Better one (well worth it!) available at

http://www.nostalgiaair.org/PagesByModel...013243.pdf
#3

You posted the same link twice. Bet you meant to send him to either

http://www.antiqueradioschematics.org/about.htm or

http://www.philcorepairbench.com/schematics.htm
#4

Thanks, right on.




Users browsing this thread:
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Hi Paulo, Welcome to the Philco Phorum. I can see why you want to find good reproduction parts. That is a bea...MrFixr55 — 11:10 PM
HiFi (Chifi) tube amp build - but my own design.
Tim, I have some bakelite sockets in my work shop that I can dig up. I believe quite a few are NOS. I will take photo...RodB — 10:03 PM
Philco 610B oscillator wiring
> The cathode as noted is wired directly to the ground side of the heater filament for that tube, not to the #17 and ...Radioroslyn — 08:12 PM
HiFi (Chifi) tube amp build - but my own design.
Tim; I noticed your post a little late, but I would take one of the junk sockets and try to break a chunk out of it wi...Arran — 08:07 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM

[-]
Who's Online
There are currently no members online.

>