Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

edison radio
#1

hey guys
any know where I can get schematic for this
http://jerseyshore.craigslist.org/atq/4126734509.html
sam
#2

Sam, it doesn't appear to be listed in N/A. Jump on that radio! I love the styling and the dual chassis. Looks to be in great shape.

Regards, Jerry

Edit: this link might give you a little more information. Dual 45s!

http://www.radiomuseum.org/r/edison_r4.html

A friend in need is a pest!  Bill Slee ca 1970.
#3

Ah, I know where two of those are near me, but one has a bad power transformer. Not sure if that is an issue with Edison radios, but might be something too look out for. Other than that, they are nice looking radios. If I could, I'd snag both from the guy I know to get a good one.

No matter where you go, there you are.
#4

You lucky people out there in the Midwest and East are in radio heaven. I doubt I could find one of those within a 400 mile radius. Still have many challenges with my Fada 46 that should take me through Winter.
I really don't have room for another console but certainly liking those old TRF sets. Not certain about the Edison but the old TRF sets I have, both don't have disconnects for the speaker or in one case the sub chassis. A real bear to work on them. Took two people to take the electronics out of my Monarch, all three parts hardwired together. Nasty!
Jerry
Regards, Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#5

Sam
Better eat your Wheaties!
Terry
#6

Sam

They are nice TRF's when done. The PP 45's do make it sound good. I have restored two with the Phonograph. The power transformers are weak and tend to have problems. I had to have a new one wound. Replace both power resistors in the amp chassis as they tend to be open. Plenty of room under the chassis to work and place new caps without opening the cans.

Good luck

Skip
#7

That's not that far from me either.
#8

Having an R32 in my wake I can say that they are definitely not the easiest sets in the world to rebuild.

The schematic for an Edison R4 is: http://www.nostalgiaair.org/Resources/839/M0021839.htm

Your schematic is on page 6.

With 3 stages of RF amplification it should be a decent receiver.
#9

I picked it up this morning. The seller was very very negotiable. It is in good shape except for the speaker cone.

Steve
#10

I'm glad you got that Steve. I noticed your posting on the alternate forum.
Regards, Jerry

A friend in need is a pest!  Bill Slee ca 1970.




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
New member
Hi. I specialize in refurbishing Predictas, but I'm in Chicago. If you can get it to me, I'd be happy to go over it. ...Bob Andersen — 06:43 PM
An attempt to remove the Field Coil from a G speaker
I have 3 G speaker, all with open Field coils. Today I pull one of the shelf and decided to try to remove the FC (spo...morzh — 06:07 PM
Philco 91 Restore Code ??
Thanks Mike. I will check them out.dconant — 05:52 PM
Philco 91 Restore Code ??
There is no such thing as bad Fluke. This said, they are expensive. A Fluke is easily 10x the price of comparable CCC...morzh — 05:45 PM
Philco 91 Restore Code ??
Hello Mike, Yes, I have 3 Fluke meters one being my first Fluke 77 and other being Fluke 87. My third is Fluke clamp -...radiorich — 05:04 PM
Philco 91 Restore Code ??
I knew that Fluke was the Cadillac so with that in mind what Fluke would you recommend I get?dconant — 03:53 PM
Philco 91 Restore Code ??
Yep. 10W is probably enough. Also, if the meter measures Farads, then it should also have that "Delta" button...morzh — 02:38 PM
Philco 91 Restore Code ??
I measured the current through the resistor I am using as a replacement for the speaker field coil and got 40ma. So that...dconant — 02:32 PM
Philco 91 Restore Code ??
No I'm not saying I don't own a DMM. I have a CCC one (Thsinde 18+). I forgot that could read caps. I did purchase a Flu...dconant — 02:28 PM
Philco 91 Restore Code ??
Are you telling me you do not own any decent DMM, that can measure capacitances from a few pF and up? Even todays CCC (C...morzh — 01:44 PM

[-]
Who's Online
There are currently 4567 online users. [Complete List]
» 1 Member(s) | 4566 Guest(s)
Avatar

>