Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

My Philco 91X, no longer ignored.
#1

I was bored this afternoon and finally decided to dig my 91X back out and at least play it a little. This radio was already recapped when I got it, but the bottom (woofer) speaker was a bit crippled from an old accident and major repairs to the cone. Basically, the old glue had caused the cone to warp over the years and it would buzz. The tweeter has some repairs too, but is in much better shape. Well, after playing it good and loud for about a half hour, the speakers seemed to come around and I ultimately enjoyed listening to the radio for two hours solid. The tone is rather good for this era of radio, especially with the tone set all the way counter-clockwise into the first position. So, it now is out and set up to be played more often instead of burried behind other radios. Icon_smile

   

No matter where you go, there you are.
#2

The 91 is a good playing set! I had one years ago it was a chairside with a big old separate speaker cabinet. In the cabinet was the dual speakers like your set. At the time I wished that it had some SW coverage.
Terry
#3

Jayce. Thats a neat looking set design. Glad to here the speaker started sounding better after playing awhile. How many tubes does that have?
#4

The 91X has nine tubes and uses push-pull 42's on the output. The dual speakers do seem to make a difference on this set. Icon_thumbup

No matter where you go, there you are.
#5

The dual speaker system was primative but agree the sound is very good!!

My model 14 LZX features the dual speakers, in fact it is playing now next to me as I type this. The 14 and 91 (early) are pretty much the same set.




Users browsing this thread:
[-]
Recent Posts
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM

[-]
Who's Online
There are currently 3205 online users. [Complete List]
» 3 Member(s) | 3202 Guest(s)
AvatarAvatarAvatar

>