BIG SCOTT CONSOLE CABINET RESTORE
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
Posts: 384
Threads: 22
Joined: Mar 2015
City: Waxahachie, TX
That will look great when you're done with it Fred!
Crist
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
I love the Scott Tasman cabinet - I think it is one of Scott's best looking sets. I probably should have held on to the AW 23 and Tasman that I had. Oh well, maybe after retirement, I'll pursue another....
Anyway, Fred, I am sure you will do your usual fine work with this one!
--
Ron Ramirez
Ferdinand IN
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
Posts: 371
Threads: 103
Joined: Jul 2011
City: Calgary, AB, CA
Very nice Fred. I always like to see your work. I have not used the Mohawk grain filler.
I have used the kind that you spread on with flat spreader and wait until it is almost dry, then use the burlap.
is Mohawk similar in application?
Dan in Calgary.
Living in Calgary Alberta
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
Hello Dan, I quess Mohawk is about the same in regards to application . I wipe it off with fresh burlap before it dries hard like wax a car. I let it haze over then wipe it smooth, then later sand it off with 240 after it has dried overnight, clean and smooth out the crevices as show in pictures, that also before it gets hard.
Posts: 4,108
Threads: 310
Joined: Nov 2013
City: Kings Park NY
It looks terrible!
I will surely take it off your hands 
You will have to show me how you did the veneer. Veneer on large areas scares me.... 
Me
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
Posts: 384
Threads: 22
Joined: Mar 2015
City: Waxahachie, TX
You are truly a craftsmen!
Crist
Posts: 1,872
Threads: 212
Joined: May 2015
City: Seattle
State, Province, Country: WA
Stunning! Thank you for all of the photos.
Posts: 1,824
Threads: 114
Joined: Jul 2014
City: Sneedville, TN
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Philco 91 Speaker Replacement
|
| The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM |
|
Restoring Philco 37-604C
|
| Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one.
Which does not m...morzh — 01:44 PM |
|
Philco 38-2 Automatic Tuning
|
| When you push the lever, you are supposed to rotate the disk to the desired station.
Then the magnetic tuning will acqu...morzh — 01:42 PM |
|
Philco 38-2 Automatic Tuning
|
| I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM |
|
Philco 91 Speaker Replacement
|
| How would I go about removing the spider from the cone?dconant — 12:04 PM |
|
Philco 38-2 Automatic Tuning
|
| Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM |
|
Does anyone make photofinish replacements?
|
| Here’s the link to the DIY photofinish section of our site:
klondike98 — 09:46 AM |
|
Delco car radio Peko vibrator converstion issues
|
| Hi Richard,
Thx for posting the schematic. As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM |
|
Delco car radio Peko vibrator converstion issues
|
| hello mr Fixr,
The Electro Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM |
|
Delco car radio Peko vibrator converstion issues
|
| How about putting a choke in the power supply?
The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM |
|
Who's Online
|
There are currently 2268 online users. [Complete List]
» 1 Member(s) | 2267 Guest(s)
|
|
|
|
 
|
The top of cabinet has severe water damage and the substrate veneer is messed up also, part of the substrate will be sectioned and repaired and all new veneer on top. The entire cabinet will be stripped and refinished to customers specs . Should look like new and will be done to factory appearance. I have done two others of this model type but was done in high gloss piano finish this one will not be gloss but a satin finish 
. So here are some pictures of this radio and some of the work I am doing, will post progression on this cabinet till work is complete and many of you guys may benefit from this.
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
