Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Precision E-200 sig gen
#1

Hi all.  I have a Precision E-200 sig generator and would like to know if it's worth recapping and how hard it would be to recalibrate afterward.  It seems like a decent piece of equipment if I can get it working right without it being a huge pita.  Any and all opinions are greatly appreciated. Thanks.  Ed
#2

If you need a signal generator then sure its worth recapping. I don't know about calibration but you can always check the frequency with a meter ( I just use the frequency meter on my multimeter). If you want to make a profit by reselling, then it depends on how much you have into it already. Check ebay's sold items to get a handle on what it might go for if working.
#3

Nah, just like restoring old stuff. It all has a purpose if it works right. This thing actually has pretty accurate signal at the middle of the dial. Drifts off at either end. And I just don't trust old caps. Like to get other peoples experiences with these things too. Thanks for the reply, much appreciated. Ed
#4

I would recap it. They don't make those anymore. So, even if you re-sell it on Ebay, you are saving a piece of history at a minimum. I have recapped a couple of signal generators myself with pretty good success. Not too hard. They do the job. They are fairly close, but to be dead on, I use a frequency counter. It wont take you long to learn the settings once you have done this a few times. You can even align the dial or mark it with a piece of tape if it isn't linear. I find my Eico is closer than my Knight, plus it as a smoother waveform output. 

If I could find the place called "Somewhere", I could find "Anything" Icon_confused

Tim

Jesus cried out and said, "Whoever believes in me , believes not in me but in him who sent me" John 12:44
#5

Hey, Tim. Thanks for the reply. I would like to get this working for essentially the same reason I like the old radios. These things do have their own history, and are the reason the old radios were able to be kept in repair. I have a H-P 3312A sig gen that I just bought on E-Bay for 50 bucks. It seems to be dead on accurate, but if I can bring the E-200 anywhere near that accuracy I'll certainly use it as well. Besides I just like fixing this stuff. Ed
#6

I think the E-200 is a very worthy candidate for restoration:

https://www.youtube.com/watch?v=-hKcL-4q5Yk

https://www.youtube.com/watch?v=DpJZOC27aYY

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#7

John, thanks for the reply, and for posting those vids. Looks like a pretty simple restore. It's actually more accurate than I at first thought, but still want to replace all those old caps and tune it up. Thanks again. Ed
#8

As a service oriented signal generator the E200 was probably the biggest seller and it does have an AVC supply which is handy at times during alignment. It also has a very accurate vernier scale which can be used to accurately repeat dial settings. I have rebuilt several and sold them to hobbyists. I also have one on my bench that I built in a crystal calibrator that produces 100KC and 1 Mhz crystal controlled heterodyne signgals and it really does a nice job. A last note: I have had to use some 1/8 inch plexiglass to make a new graticule for this model as the factory ones tend to warp very badly.
Good luck.
#9

Welcome to the Phorum eeprof!
Icon_wave




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 3067 online users. [Complete List]
» 1 Member(s) | 3066 Guest(s)
Avatar

>