1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Speaker wire colors
Steve McDonald
Junior Member
**
Posts: 35
Threads: 7
Joined: Apr 2016
City: Medford, Oregon
#1

04-11-2016, 12:57 PM
I would like to know what the wire colors were on early 1930s Philco sets. Specifically, I have an 89 THAT I CAN'T GET TO OSCILLATE. Today, they are all straw-colored. I'm sure one of the wires
Had a black leader stripe in it. I'll never find any of that! But I want it to look authentic. Which colors?
Find
Nathan Slingerland
Super Moderator
******
Posts: 1,874
Threads: 212
Joined: May 2015
City: Seattle State, Province, Country: WA
#2

04-11-2016, 02:07 PM
Hi Steve,

I'm not sure specifically about your 89 but I tried to assemble an authentic looking wire harness for my 16B in this thread:
http://philcoradio.com/phorum/showthread.php?tid=12753

You may be able to figure out the original wire colors from the portion on yours that was under the chassis - or look around the web for more pictures from better preserved examples.
Find
Nathan Slingerland
Super Moderator
******
Posts: 1,874
Threads: 212
Joined: May 2015
City: Seattle State, Province, Country: WA
#3

04-11-2016, 04:50 PM
Here's a picture of an 89B harness (not entirely faded):

   

And according to the service bulletin (#146B):

   

So the wires are green, white and green & white.
Find
Steve McDonald
Junior Member
**
Posts: 35
Threads: 7
Joined: Apr 2016
City: Medford, Oregon
#4

04-11-2016, 06:07 PM
Hmmmmmm...I wonder if I could make that Green/white wire out of a white wire and a green Sharpie......? lol
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I have been playing the radio for a while now and doing well. Turned it on today and all I got was a whole lot of noise....dconant — 09:39 AM
Rusty Tuning Condenser
Thanks guys. I think I'll give the Naval Jelly a try since I can better control where it goes.dconant — 09:23 AM
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM

[-]
Who's Online
There are currently 3536 online users. [Complete List]
» 2 Member(s) | 3534 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration