1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Model 46-420 code 121 AVC
RadioBob
Junior Member
**
Posts: 3
Threads: 1
Joined: Apr 2016
City: Tucson, AZ
#1

04-14-2016, 07:55 PM
I am reviving a Philco 46-420 and I have a question about the AVC circuit. In previous restorations I am accustomed to seeing an RC circuit filtering the audio signal off the top of the volume control pot. In this model schematic I find the “R” but not the “C”. Can you instruct me in how the AVC works in this model? Thanks for your help. RadioBob
Find
klondike98
Phorum Moderator
******
Posts: 5,091
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#2

04-14-2016, 10:41 PM
Welcome to the Phorum!
Icon_wave
Sorry, can't answer your question but I'm sure one of the crowd here will chime in soon.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
RadioBob
Junior Member
**
Posts: 3
Threads: 1
Joined: Apr 2016
City: Tucson, AZ
#3

04-14-2016, 10:48 PM
(04-14-2016, 10:41 PM)klondike98 Wrote:  Welcome to the Phorum!
Icon_wave
Sorry, can't answer your question but I'm sure one of the crowd here will chime in soon.

Oops!  Sorry.  I just found the "C".  It was not where I expected it.  It makes sense now.  This is a great forum; I hope to be able to contribute soon.  Thanks.  RadioBob
Find
Mondial
Phorum Expert
*****
Posts: 1,114
Threads: 14
Joined: Feb 2013
City: Irvington, NY
#4

04-14-2016, 11:05 PM
In this set, the AVC voltage is obtained from the diode detector through R11 and then filtered by C12. Its a bit unusual in that the voltage is not taken off the detector output to the volume control, but the DC voltage is the same at both points. They also use the other diode of the 7C6 directly across the AVC line, probably to develop contact potential negative voltage to set the no signal grid bias on the RF converter and IF tubes.

http://www.nostalgiaair.org/pagesbymodel...013597.pdf
Find
RadioBob
Junior Member
**
Posts: 3
Threads: 1
Joined: Apr 2016
City: Tucson, AZ
#5

04-15-2016, 10:38 AM
Thank you, Mondial, for the AVC operation description. RadioBob
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Rusty Tuning Condenser
Thanks guys. I think I'll give the Naval Jelly a try since I can better control where it goes.dconant — 09:23 AM
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM

[-]
Who's Online
There are currently 3894 online users. [Complete List]
» 2 Member(s) | 3892 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration