Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

38-116 speaker
#1

hey guys
I have a 38-116 speaker.  cone has small tear other then that great
NO   voice coil on cone bad thought rewire it ?
has any one had luck trying to get paper cone off speaker frame
with out tearing it ?

thanks sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#2

Some of the spkr cones are held down with sheet metal screws along the perimeter. If not you'll have to use a solvent like acetone or mek to remove the adhesive. Start small by wetting edge and work your way around slowly. So do you have the chassis and cabinet too??

Have you tried to measure the resistance of the vc as close the coil as you can eliminating the possibility of a bad connection or bad hb coil?

Terry
#3

Ed Locker showed me how to use acetone to remove speaker cones in this manner several years ago. The trick is not to use too much acetone...just a little from a dropper is the preferred way to apply it...and be patient as it may take more than one application of acetone.

--
Ron Ramirez
Ferdinand IN
#4

 Terry
I tried testing bottom of cone where winding is but get nothing 
I see 1 coil wire on right but don't see a wire on left
Should have some continuity.  I Ohmed out green and white wires
Going to it. Has .05 ohms  
Did get cone screw out and disk up just have to remove cone 
I have to also look for cabinet 
Little miss happen a work with it 
Sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#5

Hey Sammy,
I know a old guy who is a real pita that has a spkr from a 37-116. It does have some paper damage but he thinks it's serviceable. Now a nice young clean cut guy like you could probably have it if this old fart can find it.

Terry
#6

lol Icon_lol
I seen that old fart`s house he`ll never find it Icon_shh

not kirk

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 89 indicator light.
Is there some trick to getting the indicator lamp evenly spaced between the frequency bands? Seems like no matter what I...Jim Dutridge — 04:37 PM
Philco 40-120C Restoration
Hi David, Check the cathode bias resistor, it may have changed value. That will affect grid bias, etc. Also, verif...MrFixr55 — 03:26 PM
Philco 91 Restore Code ??
Hi DConnat,  Yes, the 42s are in Pentode Mode, cathode bias.  I am using the schematic from the Philco Library, Link ...MrFixr55 — 03:04 PM
Philco 40-120C Restoration
Not my radio just trying to help. DavidDavid — 02:48 PM
Philco 91 Restore Code ??
Thanks Rod. Since the screen grid is not tied to the plate then my tubes are pentode right? I see the candohm ties to th...dconant — 02:29 PM
Philco 91 Restore Code ??
Yes, you can look at the schematic. When the output tube screen grid is connected directly to the plate then it's wired ...RodB — 01:51 PM
Philco 91 Restore Code ??
Can someone tell me if my 42 tubes are connected triode or pentode in fixed or cathode bias? How could I tell by looking...dconant — 10:47 AM
Philco 40-120C Restoration
Hello David, that is great news about the tubes source being local ! Sounds like you got good start on the radio . ...radiorich — 09:41 AM
An attempt to remove the Field Coil from a G speaker
Mike; I've only run into a speaker with an open filed coil twice, and they were on newer speakers from the 1940s. One ...Arran — 12:48 AM
An attempt to remove the Field Coil from a G speaker
Arran Yes, this is my plan for now and what do I got to lose, this is not even the speaker from this radio, but one o...morzh — 10:44 PM

[-]
Who's Online
There are currently 2217 online users. [Complete List]
» 3 Member(s) | 2214 Guest(s)
AvatarAvatarAvatar

>