Posts: 15,843
Threads: 555
Joined: Oct 2011
City: Jackson, NJ
The second radio I started today.
It is a brown backelite 38-12.
I bought it for a very good price of $40 and the shipping was reasonable. The lady wrapped it in very few plastic store bags plus put some pieces of bubble wrap in between the tubes, despite my advice, but somehow the radio was lucky and arrived totally undamaged. Or so I think.
Here are the pics:
Front. I have already bought the dial cover from Mark Palmquist
Back
Dial/speaker
Chassis' top. Dusty, aren't we.
Bottom of the chassis. The full opposite of the top, no pun intended.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 15,843
Threads: 555
Joined: Oct 2011
City: Jackson, NJ
Typical....on the speaker the xfmr primary's open. I might have the transformer though.....
Field is good and this is what's important.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 04-23-2016, 08:07 PM by morzh.)
Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
You may want to consider put a thin piece of clear plastic between the dial and pointer.
Common with the pointer tearing up the foil on the dial.
Terry
Posts: 15,843
Threads: 555
Joined: Oct 2011
City: Jackson, NJ
All tubes are very strong.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 4,384
Threads: 412
Joined: Jun 2011
City: Boston
State, Province, Country: Massachusetts
That is a great suggestion Terry, I learned the hardway and now must endure a very plain looking Radio Daze repro on one of my Philcos.
Paul
Tubetalk1
Posts: 15,843
Threads: 555
Joined: Oct 2011
City: Jackson, NJ
Terry
I will see if it is close enough, will do that. Thanks.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 15,843
Threads: 555
Joined: Oct 2011
City: Jackson, NJ
I resumed Sunday after Kutztown.
Removed the old output transformer, had to drill out the rivets.
Rebuilt both caps yesterday, recapped everything, three resistors had to go.
Opened and cleaned the volume pot.
Today replaced the output xfmr, having riveted it to the speaker.
Connected everything, powered it up.
Works fine, receives stations across the dial.
Need to align obviously.
Need to remove and wash the tuning cap, very dirty.
Then the alignment.
Then gluing the dial cover, cleaning the cabinet, maybe learning how to polish it a bit, assemble the radio.
Done for today.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 15,843
Threads: 555
Joined: Oct 2011
City: Jackson, NJ
Removed the tuning cap. It's a pain but affer 620 with its switch and all it was almost a breeze.
Now it is soaking. The gromnets solidified and crumbled. I could've left it since it was working fine but there is a lot of dirt in it and around and it feels wrong. Plus it has the string. Simple but.....I hate strings.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 15,843
Threads: 555
Joined: Oct 2011
City: Jackson, NJ
Well the ekectrical part's done.
Put all back in, aligned it.
Realized the volume pot is acting up. Opened it again, cleaned with alcohol, then some Deoxit plus taking the shaft out and bending the wiper just a tad. Then it worked nicely.
Now I am trying to manufacture the cloth holding board out of some Foam Core board.
Tomorrow will see.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 15,843
Threads: 555
Joined: Oct 2011
City: Jackson, NJ
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 5,091
Threads: 270
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
Posts: 15,843
Threads: 555
Joined: Oct 2011
City: Jackson, NJ
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 667
Threads: 11
Joined: Sep 2014
City: Bellmawr, NJ
Posts: 15,843
Threads: 555
Joined: Oct 2011
City: Jackson, NJ
You're right. I will.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Users browsing this thread: 2 Guest(s)
|
|
Recent Posts
|
|
Philco Model 80 Transformer resistance
|
| Just forget this number, it is useless anyway.
Simply proceed with your project.morzh — 10:08 PM |
|
Philco Model 80 Transformer resistance
|
| My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM |
|
Philco Model 80 Transformer resistance
|
| Thanks for the quick reply!
Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM |
|
Philco Model 80 Transformer resistance
|
| The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM |
|
Philco Model 80 Transformer resistance
|
| I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM |
|
Rusty Tuning Condenser
|
| I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM |
|
38-10T chassis Restoration begins
|
| Hello Dconant ,
they sold mica to use as a insulator between transistors and their heatsinks too.
Rob I will remove th...radiorich — 02:52 PM |
|
38-10T chassis Restoration begins
|
| Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM |
|
38-10T chassis Restoration begins
|
| Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM |
|
38-10T chassis Restoration begins
|
| It is acceptable but not desirable.
Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM |
|
Who's Online
|
There are currently 3212 online users. [Complete List]
» 2 Member(s) | 3210 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
