Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

1930 model 96
#1

I normally don't venture into local antique shops but did so today with my dad, who knows the owner. He has this 1930 Philco high boy that is being used as a daily driver. He plays it all day every day he's open. It sounds good so at minimum the electrolyitics have been replaced. He needs space and offered it to me for  $70. The cabinet has a lot of scratches and probably needs refinishing. I certainly don't need another console but this seems like a good deal. What do you guys think? 

Greg V.
West Bend, WI
Member WARCI.org
#2

   

Greg V.
West Bend, WI
Member WARCI.org
#3

 I like the style of the cabinet. Based on some google pics of the 96 looks like that is the original grill cloth and in good condition. Depends on how much you want it as to price to pay.
#4

Greg, I bet that that 96 is unrestored and playing on all its original parts. As far as I recall, the 96 has no electrolytics, but uses a paper capacitor block for filters.

Actually I would not be surprised if it has been playing as is every day in the store . I have a 
Philco 77 which is unrestored and totally original, right down to the Philco globe tubes. I don't use it much, but it still plays great when I power it up
#5

It is a good deal.
I have this very radio I have yet to restore.
It is a good looking and one of the few with that leaves pattern.
For 70 bucks it is a good deal. Not super, not stellar, just good.
In case you want it.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#6

It's possible it was untouched...there was so much junk...er, I mean priceless antiques... around and on it I couldn't get a look at the back. If those were the original filters they were still doing a great job after 86 years....there was no hum at all! I even turned the volume down to check. I will give it some thought....and see how much I sell (or buy...) at the WARCI meet next Sunday.

Greg V.
West Bend, WI
Member WARCI.org




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM

[-]
Who's Online
There are currently no members online.

>