Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Bathtub Block 3903AH ?
#1

Can't find a listing on this one.
Assume it is a .01 Block

It was changed at some point according to Philco to 3903 SG . Nothing on it either.

Bob T
#2

Yes is a 0.01 uF cap as seen below:

[Image: https://dl.dropboxusercontent.com/u/5462...903-AH.jpg]

3903-SG would be a lower melting point wax than the 3903-0SG  (the O was for higher temp wax) but should have the same configuration.  See Ron's post of Bakelite Condenser Data or Chuck's Bakelite Block Values page.
#3

(05-29-2016, 05:25 PM)klondike98 Wrote:  Yes is a 0.01 uF cap as seen below:

[Image: https://dl.dropboxusercontent.com/u/5462...903-AH.jpg]

3903-SG would be a lower melting point wax than the 3903-0SG  (the O was for higher temp wax) but should have the same configuration.  See Ron's post of Bakelite Condenser Data or Chuck's Bakelite Block Values page.

Thank you Sir. Only 6 more to go on the 16

Bob T
#4

If you have not seen it, here is a nice thread on restuffing these caps.

http://philcoradio.com/phorum/showthread.php?tid=9107
#5

(05-30-2016, 07:04 AM)klondike98 Wrote:  If you have not seen it, here is a nice thread on restuffing these caps.  

http://philcoradio.com/phorum/showthread.php?tid=9107

I use to use my Commercial Heat Gun to remove the Blocks. No More

Before Doing this Procedure check and know what your Block Contains. Blocks containing Resistors DO NOT DRILL


Now I have used the method by cutting the wires on top of Block where the inside parts are soldered. Then drilling a small size drill dead center of Tar , yes drill right on through the Caps inside.

Once you have drilled to the Bakelite, stop.  Then I use a fine thread sheet rock screw 1 1/2" long
Thread it in slowly into your drilled hole with a Phillips screwdriver. You will be amazed as you seen the entire Tar block Caps and all slowly come out.

Has not failed me yet.
Been using it on the 14 Block 16B I am working on.
Just remember to FIRST cut the wires on top where the internal parts are soldered to.

This is not my idea, I believe I saw this method over on Chuck's Site.


Bob T




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently 3878 online users. [Complete List]
» 1 Member(s) | 3877 Guest(s)
Avatar

>