Posts: 94
Threads: 9
Joined: Feb 2013
City: Monroeville, PA
I am curious about the best way people have found to open can capacitors for restuffing. The one I am currently trying to do is a Philco Part #7558-S.
Any tips, pointers or suggestions are appreciated.
Thanks, Bill
Posts: 5,071
Threads: 269
Joined: Nov 2012
City: Bandon
State, Province, Country: OR
Bill, what radio is it on? The can cap in my 60MB was straight forward and with a little unbending of the metal tabs the tar encrusted caps slid out with the fishpaper. Others will have to comment on other models.
If you are speaking about those black bakelite block caps, then here's a t hread for those.
Posts: 15,511
Threads: 544
Joined: Oct 2011
City: Jackson, NJ
There are all kinds of cans. Those rectangular ones like in 20/70/90 are the easuest. Just fishpaper. Undo brackets, it slides out. I always salvage the GND wire. No potting after restuff.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 94
Threads: 9
Joined: Feb 2013
City: Monroeville, PA
Posts: 736
Threads: 26
Joined: Jun 2013
City: Hayward, California
You can also use a tubing cutter to open them .
Posts: 5,071
Threads: 269
Joined: Nov 2012
City: Bandon
State, Province, Country: OR
Here's a service tip from Chucks site:
http://www.philcorepairbench.com/tips/svctip46.htm
There are some pics in that 60MB post of the round can type being stuffed. I have used a hacksaw blade to open, but I get a neater cut with a box cutter blade. I place the blade on the can with a little pressure and roll the can back and forth working my way around the can. As with a pipe cutter, you go slow making the cut in the can a little deeper each rotation.
Posts: 94
Threads: 9
Joined: Feb 2013
City: Monroeville, PA
Thanks everyone. I think I have all that I need to get started. The only thing remaining is a little bit of time.
Best Regards, Bill
Posts: 15,511
Threads: 544
Joined: Oct 2011
City: Jackson, NJ
I use pipecutter, but it smushes the can a bit. Not a very precise yool when dealing with a very soft thin metal.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 5,071
Threads: 269
Joined: Nov 2012
City: Bandon
State, Province, Country: OR
Yep, mike, thats why I use the box cutter blade. Sharper, narrower than pipe cutter.
Posts: 15,511
Threads: 544
Joined: Oct 2011
City: Jackson, NJ
I recently started using bandsaw. Have it at work.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 667
Threads: 11
Joined: Sep 2014
City: Bellmawr, NJ
ultilty knife works really well,,stab it in and work it around,,about 1 " from the base
Posts: 177
Threads: 19
Joined: Feb 2014
City: The Motor City,Detroit MI
I just want to add that after cutting, I iron out the dents on the can by slipping in a large socket from my toolbox and rolling.
Posts: 15,511
Threads: 544
Joined: Oct 2011
City: Jackson, NJ
I simply try to cut it where it won't be noticeable too much.
Say the cap is held by a clamp by its bottom side. So I cut it such that the cut will be concealed by the clamp.
If a cap is screwed to the chassis and has the cap separated by a groove, then I cut right at the groove and then simply glue the cap in place as it is not mechanically stressed.
If a cap is screwed but has the indent at the bottom, which is about 1/8" wide, then I cut at the very upper border of the indent, which serves two purposes: 1) the main cut part has no narrowing so the guts are extracted easier, and 2) the indent then, after some manipulation, can be inserted inside the main part which still preserves the caps' looks though the indent itself becomes a smaller groove.
Any way of cutting without smooshing the can is good.
When using band saw which produces very accurate cut, the cap has to be advanced a little at the time, first one turn, and then another, or else the saw will pick up the can damage it somewhat, plus there is a possibility of tossing it across the room. So need to be careful.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 1,824
Threads: 114
Joined: Jul 2014
City: Sneedville, TN
I use a cutting disc on a Dremmel tool, and cut carefully around at a point where the clamp will cover the cut. I use this aluminum tape that I bought at an auto supply store to tape it together. I cut a strip narrow enough so that it will be completely covered by the clamp. If no clamp, as on yours, then the aluminum tape is close enough to not be easily noticeable. In that case I would cut about 1/4 inch above the base, and cut the strip of tape about 1/2 inch wide.
Posts: 177
Threads: 19
Joined: Feb 2014
City: The Motor City,Detroit MI
There are many different style cans out there. The one Bill shows is the one I like to restuff. The cut can be made just under the top where it's not noticeable. And when restuffed and glued back together, the can still has strength if you should grab it while handling the chassis.
Users browsing this thread: 2 Guest(s)
|
Recent Posts
|
Philco 89B code 123 newbie
|
Hi all and thanks for the great responses! I went with a can left over from another radio, kinda scratched up but it do...Kurt P — 04:35 PM |
Clear Schematic for 41-255
|
AH Just noticed 1 error on my cleaned-up schematic...
Part # 27 - the 8uf electrolytic cap...The lead that is marked RE...patrician56 — 04:10 PM |
Clear Schematic for 41-255
|
Hi Ross,
I don't know if you still need a clear schematic for the 41-255 but here is one that I cleaned up. I added pin...patrician56 — 03:45 PM |
AC/DC Transformer-less Sets
|
Joseph,
Thanks for the follow up.
MrFixr55,
Thanks for the info. I was aware of the "Current Wars"...PeterN — 03:32 PM |
AC/DC Transformer-less Sets
|
Fantastic report, Mr. Fixr! I had never read about AC/DC sets originally running at a higher price than AC-only models, ...jrblasde — 01:21 PM |
49-504
|
Also wheni first power on the 7a8 gets very bright more than normal not sure what I did wrongphilco4me — 12:53 PM |
49-504
|
Hello all
I am doing a 49-504 and in section 4 I see C401is that a 5mmf ? I did not see that when I replaced the caps.
...philco4me — 12:47 PM |
Looking for place to donate unique Philco Philco J-1930 Prototype
|
Thx for the description. I thought that it had to have a single 10 - 12" Sensor.
Congrats on restoring the GE and...MrFixr55 — 10:12 AM |
AC/DC Transformer-less Sets
|
Some of the original Edison DC generators were in use until the 1940s. The NYC subway and electrified Long Island Rail ...MrFixr55 — 09:39 AM |
Samlex heavy-Duty bench supply filter question
|
I suggest sticking with the original values. Depending upon the design if you increase the cap values too much the incre...DaleHCook — 08:55 AM |
Who's Online
|
There are currently no members online. |
|
|