1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 40-190 Missing Resistor
k9gpc
Junior Member
**
Posts: 3
Threads: 1
Joined: May 2016
City: Rochelle, IL
#1

05-31-2016, 08:29 PM
I am refurbishing a beautiful Philco 40-190 for a friend of mine. I've replaced all the resistors and caps after checking the service bulletins. However there is one resistor that I cannot find: The 10K resistor (1B) that is supposed to be in parallel with a 250 pf cap (1A). There is no sign of it every being there; the solder joints are obviously old. Could this be the result of another service bulletin?

Tom


Attached Files Image(s)
   
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#2

05-31-2016, 09:11 PM
(1A) and (1B) are inside the loop antenna. There is usually no need to worry about these components as they are not exposed to any significant voltage.
--
Ron Ramirez
Ferdinand IN
Find
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#3

05-31-2016, 10:07 PM
Welcome to the Phorum!
Icon_wave
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
k9gpc
Junior Member
**
Posts: 3
Threads: 1
Joined: May 2016
City: Rochelle, IL
#4

06-01-2016, 06:21 AM
(05-31-2016, 09:11 PM)Ron Ramirez Wrote:  (1A) and (1B) are inside the loop antenna. There is usually no need to worry about these components as they are not exposed to any significant voltage.

Thanks for the info. Probably never would have looked there.....Tom
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#5

06-01-2016, 02:07 PM
It's best to not unwrap the loop antenna covering as it has wires embedded in it which serves as an electrostatic shield to reduce noise. Cut the covering open, and you destroy the shield. The loop will still work okay, but I would rather leave it alone.
--
Ron Ramirez
Ferdinand IN
Find
k9gpc
Junior Member
**
Posts: 3
Threads: 1
Joined: May 2016
City: Rochelle, IL
#6

06-02-2016, 06:19 AM
(06-01-2016, 02:07 PM)Ron Ramirez Wrote:  It's best to not unwrap the loop antenna covering as it has wires embedded in it which serves as an electrostatic shield to reduce noise. Cut the covering open, and you destroy the shield. The loop will still work okay, but I would rather leave it alone.

trust me. I will not open it....tom
Find
« Next Oldest | Next Newest »




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM

[-]
Who's Online
There are currently 4370 online users. [Complete List]
» 2 Member(s) | 4368 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration