1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
rewire philco90 highboy speaker
mg34.42
Member
***
Posts: 89
Threads: 36
Joined: Dec 2013
City: Tulsa, OK
#1

08-04-2016, 08:36 PM
what is the best way to re wire a philco90 speaker and a good way to open up the bake lite plug it looks to me the best way is to recon it and dose any have the cloth wire for this sorry about the last post I have been up for over 24 hours working my regular job
ben
(This post was last modified: 08-04-2016, 09:02 PM by mg34.42.)
Find
morzh
Odobenus rosmarus
*****
Posts: 15,511
Threads: 544
Joined: Oct 2011
City: Jackson, NJ
#2

08-04-2016, 08:46 PM
Mg.....what exactly do you want to do? Plug or something else?
Some punctuantion and more accurate writing goes a long way when you try to formulate a thought so others coild understand. Icon_smile
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 08-04-2016, 09:38 PM by morzh.)
Find
sam
Phorum Expert
*****
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
#3

08-04-2016, 08:55 PM
Mike
Mike  mike
Look at what you wrote  Icon_confused
Just ask him to rephrase the question

Sam
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Find
klondike98
Phorum Moderator
******
Posts: 5,071
Threads: 269
Joined: Nov 2012
City: Bandon State, Province, Country: OR
#4

08-04-2016, 08:56 PM
Hi Ben, I think you are adking about replacing the speaker wires. There was a philco 70 speaker rewire discussion recently that might help.

http://philcoradio.com/phorum/showthread.php?tid=15052
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Samlex heavy-Duty bench supply filter question
Hello Everyone, I have one of my Heavy-duty bench powersuplies made by Samlex it's 13.8 volt dc 20-25 amp supply. What I...radiorich — 11:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a Glaser Sears changer which Philco's engineers thought was an upgrade over a VM, but in retrospect I'd prefer the ...jeibner — 10:39 PM
AC/DC Transformer-less Sets
Joseph, Thank you for the confirmation. I knew that there must be more to the Transformer-less AC/DC radios than the ...PeterN — 10:30 PM
AC/DC Transformer-less Sets
Good evening, folks. Power station engineer here! The east coast had pockets of DC-only power well into the twentieth...jrblasde — 10:11 PM
AC/DC Transformer-less Sets
Model 40 does not have a rectifier, so it would be a DC only model. This however does not say anything about using...morzh — 08:01 PM
AC/DC Transformer-less Sets
I was wondering if anyone knows if these AC/DC transformer-less sets were actually used on 110v DC anywhere, and when. ...PeterN — 06:35 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM
Jackson 665 j2 schematic request
FIXED!daveone23 — 03:55 PM
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM

[-]
Who's Online
There are currently 5159 online users. [Complete List]
» 5 Member(s) | 5154 Guest(s)
AvatarAvatarAvatarAvatar
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration