Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Fisher 1800 receiver
#1

  Well this was what I was hoping to get at this auction. But went too high for me.
http://bid.schulmanauction.com/lot/26234...ef=catalog
#2

I know this is going to sound crazy...but $632.51 is cheap compared to what its sibling 800-C receivers usually sell for. And I think the 1800s, being more rare than the 800-C, usually command a premium. Most likely, whoever bought this is going to flip it for double the money.

--
Ron Ramirez
Ferdinand IN
#3

Looking closely at a chassis picture with voltage/rating stamped on it, it indicates 220-240V AC!
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#4

I read somewhere that the 1800 was designed for export and/or for sale to military personnel stationed outside the USA.

--
Ron Ramirez
Ferdinand IN
#5

Thanks Ron, it might be a killer for someone here in the states to purchase unless it is easily modified? The seller might have pointed that out. KCMike , you might have been lucky to not be high bid.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#6

I seen that on the chassis and thought it would have a selector some where to change to 120v.
Learn something new everyday.
Your right Jerry, glad now I no buy.Icon_smile
#7

Mike, perhaps it is something easy but would not be a switch change or it would have listed it as a dual voltage. Someone else has bought it and I hope they know more than we do. I will yield to Ron's knowledge of these lovely receivers.
Best, Jerry

A friend in need is a pest!  Bill Slee ca 1970.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently 3871 online users. [Complete List]
» 1 Member(s) | 3870 Guest(s)
Avatar

>