Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

GE F-96 wood repair
#1

I'm working on a F-96 and it has a chunk taken out of it.


[Image: http://i.imgur.com/4fmxl9r.jpg]
Anyone have a better sense of wood identification than me? I'm going to try a veneer patch, but I suppose I better know what wood I'm looking for.
#2

Has the side pulled away for the top?? The contour of the side doesn't look like it matches the top. Are you thinking of refinishing the whole cabinet or just repairing this issues?

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

I am not an expert, but that looks like mahogany, AKA luan plywood.
#4

Im refinishing it completely. I've reglued the loose edge to the top. I've stripped and sanded. I have some veneer samples coming.

I'm not sure how to approach the missing substrate issue.
#5

(08-10-2016, 08:05 PM)kc5gym Wrote:  I am not an expert, but that looks like mahogany, AKA luan plywood.

No, It's not Luan plywood, it's one of the mahogany look a likes, sapele. or possibly quartersawn makore. G.E listed what sort of veneers they used in their advertising and I think that they liked to use one of those veneers, particularly of the ribbon striped variety, on their cabinets in the 1938 and 39 model years.
 
http://www.wood-database.com/lumber-iden...ds/makore/

http://www.wood-database.com/lumber-iden...ds/sapele/

Regards
Arran
#6

(08-12-2016, 03:38 AM)Arran Wrote:  
(08-10-2016, 08:05 PM)kc5gym Wrote:  I am not an expert, but that looks like mahogany, AKA luan plywood.

No, It's not Luan plywood, it's one of the mahogany look a likes, sapele. or possibly quartersawn makore. G.E listed what sort of veneers they used in their advertising and I think that they liked to use one of those veneers, particularly of the ribbon striped variety, on their cabinets in the 1938 and 39 model years.
 
http://www.wood-database.com/lumber-iden...ds/makore/

http://www.wood-database.com/lumber-iden...ds/sapele/

Regards
Arran

That Makore looks like a possibility.
#7

(08-12-2016, 07:40 AM)Tgace459 Wrote:  
(08-12-2016, 03:38 AM)Arran Wrote:  
(08-10-2016, 08:05 PM)kc5gym Wrote:  I am not an expert, but that looks like mahogany, AKA luan plywood.

No, It's not Luan plywood, it's one of the mahogany look a likes, sapele. or possibly quartersawn makore. G.E listed what sort of veneers they used in their advertising and I think that they liked to use one of those veneers, particularly of the ribbon striped variety, on their cabinets in the 1938 and 39 model years.
 
http://www.wood-database.com/lumber-iden...ds/makore/

http://www.wood-database.com/lumber-iden...ds/sapele/

Regards
Arran

That Makore looks like a possibility.

 Better strip some of the original finish off, just to make sure, G.E was like many manufacturers in that their cabinets had a tinted finish over everything to even out the variations in wood grain.
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Made mistake & did not label connection
Hi John, I don't have this radio, but I can supply some info: Based on your pic, pins 7,8 and 1 are used together, go...MrFixr55 — 02:02 PM
New Philco Repair Bench
As far as I know, the Repairbench does not work, and has not been working in a while. Chuck (we had that campaign looki...morzh — 01:33 PM
Radio city products 664 schematic request
Need a schematic or manual for the 664. The 663 may be similar.daveone23 — 12:38 PM
New Philco Repair Bench
Thanks Gary.dconant — 12:16 PM
New Philco Repair Bench
I tried accessing the site through our library and got the same response. It's reported to our tech gurus. GaryGarySP — 11:50 AM
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM

[-]
Who's Online
There are currently 4565 online users. [Complete List]
» 1 Member(s) | 4564 Guest(s)
Avatar

>