Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco P-337
#1

This is nice - I've not seen this one before. Anyone have any further history or information ? http://cgi.ebay.com/320411541415
#2

It's a UK Philco set, never was sold here in the USA.

Most UK Philco models used chassis which were built in Philadelphia with cabinets produced in England. The styling of UK Philco models is quite different from USA Philco sets.

--
Ron Ramirez
Ferdinand IN
#3

I heard a story that many of the British Philcos often used Canadian built chassis or were assembled from parts imported from Canada due to the favorable trade situation since Canada was part of the British Commonwealth/Empire, there is British Philco that used the same cabinet as a Canadian Philco model 3118 from 1935.. Many of the American car makers did the same, built cars in Canada for export to Britain, Australia, New Zealand, and other Commonwealth countries.
I think that this set may have been British designed and produced, it's layout and style doesn't resemble any Canadian made set that I have seen. I can tell you this much, his shipping cost is out to lunch, it should not cost $117 to ship a 20 pound radio to Canada (if it even weighs that much being a battery set) and what sort of packing materials weight ten pounds unless it's packed in a crate or packed with sawdust? Ebay fee avoidance perhaps?
Best Regards
Arran
#4

I checked his shipping cost and the International Priority rate is about right. However, Canada is cheaper than say, France. It would still be about $73 to there.
If its any consolation thats about the same price as to here in Puerto Rico USA. It looks heavy.
#5

The strange part is that the shipping rate to Canada is lower on a cathedral radio he is also trying to sell, and one of those would weigh more more then that Philco with the transformer iron they come with. In any case these dolts at the US postal service are wondering why business is down and why they are losing money. Truth be told I don't buy radios this way anymore, out of five ebay radios two were smashed, any radios I get now have to come home with me.
Best Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Correct model 84 Ac plug an cord type
From what I read Philco went to using brown rubber power cords in 1936, so cloth was used in the 1935 and earlier models...Arran — 11:25 PM
Correct model 84 Ac plug an cord type
Hi Bruce, I have not worked on an 84, but in general, power cords for almost any radio prior to 1938 was cloth covered...MrFixr55 — 08:34 PM
Restoring Philco 38-14
OK, well, so after staring at the sch again, I realized the problem had to be the #12/12A padder. I put a scope on the o...morzh — 08:15 PM
Correct model 84 Ac plug an cord type
Hello Bruce, I mostly use brown far as my cloth powercords go ! Here is the plug that I have used bakelite Acorn style...radiorich — 08:05 PM
Correct model 84 Ac plug an cord type
Looking for as correct as can find the right Ac plug an the correct colored cloth line. Ive seen many old photos but mos...Bruce — 04:13 PM
Restoring Philco 38-14
Rod Two Y-caps make sense if you use them from L/N to the chassis; this is only makes sense in the transformer radios...morzh — 10:11 AM
Restoring Philco 38-14
Mike, I'm curious about a specific use of he Y cap. Lately I've seen a single cap across the power transformer primary. ...RodB — 09:01 AM
Restoring Philco 38-14
hello morzh , That sounds like a plan ! Sincerely Richardradiorich — 07:45 AM
Restoring Philco 38-14
Richard, It helped some, but I still had the whining when engaging the rear power strip (I did not realize it was fro...morzh — 07:07 AM
Restoring Philco 38-14
Hello morzh, Yes , that dreaded hum in my room where i do alighment I have my cable modem and router plus desktop plus ...radiorich — 11:25 PM

[-]
Who's Online
There are currently no members online.

>