1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 610 Radiobar restoration Chronicle
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
#1

10-15-2016, 05:40 PM
I bought this radiobar recently and WOW it is a mess...
Defects:
1. Rotten feet
2. Destroyed lid.. Fell apart in my hand...
3. 95% covered in mold
4. No chassis
5. No speaker
6. Rusty chrome Icon_sad
7. Many separations in cabinet and dried out glue...

Pluses
1. Feet can be easily reproduced
2. I have all the lid pieces and the mirror.
3. Mold destroyer and sunlight Icon_lol
4. Found a 610 chassis and 8" speaker in my store room in a bad cabinet
5. Chrome should clean up real good but I may have it redone...
6. It cleaned up amazingly and I can glue all the separations...

I started by thoroughly washing the radio in the sun with mask and goggles.. Warm water and a wet towel.. Took an hour and 5 rinses... I am flattening the lid sides now and drying out the sheets that separated. 


Attached Files Image(s)
                   
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
#2

10-15-2016, 05:44 PM
I found the chassis for it in a 610 bullet cabinet that is a real mess.. The speaker cone is bad but I would not be using it anyway...
  The main issue is that someone has worked on it and the sheet he included in the cabinet is not encouraging.. Icon_lol
They even taped off the plug!  Icon_rolleyes

I will be looking for a better chassis if anyone has one and a good correct size speaker.. 8"? 10"? 12"? 


Attached Files Image(s)
                   
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
#3

10-15-2016, 05:46 PM
I put the chassis in just to see how it will look..
I like it!!


Attached Files Image(s)
           
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
sam
Phorum Expert
*****
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
#4

10-15-2016, 06:35 PM
looking good Icon_thumbup Icon_thumbup
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
#5

10-19-2016, 12:26 PM
Ok Question..
The speaker for this... Is it only an 8"?? I am going my looking at the speaker hole in the cabinet...
Someone offered me a 37-650 chassis and speaker but I am not sure if it will fit....

Any ideas?

Kirk
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#6

10-19-2016, 01:18 PM
What size is the hole of the speaker mounting board in the cabinet?

You can always enlarge it if necessary (or, preferably, cut another speaker mounting board and keep the original in case someone wants to go back to original)...
--
Ron Ramirez
Ferdinand IN
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

[-]
Who's Online
There are currently 5437 online users. [Complete List]
» 1 Member(s) | 5436 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration