Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 39-116
#1

Where can I find the tube layout and schematic for a Philco Model 39-116?
#2

Welcome to the Phorum!
Icon_wave

A free schematic can be found on nostalgiaair.org
http://www.nostalgiaair.org/Resources/266/M0013266.htm

The Service Bulletin #310 is available on the audiophool site:
http://www.audiophool.com/Philco.html

( the reader for the djVu file is here; https://www.cuminas.jp/en/downloads/download/?pid=1 )

A more readable set of schematics and info can be had for a few bucks from Chuck.

www.philcorepairbench.com/schematics.htm

For more resources that might be helpful, see:

http://philcoradio.com/phorum/showthread.php?tid=14950
#3

Thank you!  That's great information!  I've got a check going out to Chuck today!
Tim
#4

(09-28-2016, 08:13 PM)klondike98 Wrote:  I just watched a Philco factory tour video on Youtube. Here is a link:
https://www.youtube.com/watch?v=kanPsUDyKrU
Welcome to the Phorum!
Icon_wave

A free schematic can be found on nostalgiaair.org
http://www.nostalgiaair.org/Resources/266/M0013266.htm

The Service Bulletin #310 is available on the audiophool site:
http://www.audiophool.com/Philco.html

( the reader for the djVu file is here; https://www.cuminas.jp/en/downloads/download/?pid=1 )

A more readable set of schematics and info can be had for a few bucks from Chuck.

www.philcorepairbench.com/schematics.htm

For more resources that might be helpful, see:

http://philcoradio.com/phorum/showthread.php?tid=14950
#5

Hi ozo,
Welcome to the Phorum!
Icon_wave
I think you're trying to post something...give it another try.
#6

The remarks re: the youtube video of Philco's Factory Tour was my first post and had to go through moderation. I mentioned it because it is free but in the list of resources it was not. There are many videos on you tube but you have to look. Just plug in your model number and there may be videos of it including repair tutorials.

Here is an example of a youtube video of a huge Philco radio collection I liked.  
https://www.youtube.com/watch?v=7Eb35g1vqH4

Yea I am a new guy and glad to be here. I started out collecting vintage audio gear like receivers, amps, turntables, and tape decks but could not afford tube amps. Then I got my first tube radio and now have five. Three are Philcos; 48-482, 39-75, and a 46-421.
#7

Thanks for watching, Ozo. Glad you liked my videoIcon_smile

Greg V.
West Bend, WI
Member WARCI.org
#8

(10-18-2016, 06:43 PM)NostalgiaRadioTime Wrote:  Thanks for watching, Ozo. Glad you liked my videoIcon_smile

It is well done and I liked the earlier one too. I was watching the 2016 video for a while before I realized it was the same collection only on steroids. Icon_clap
#9

Ha! It's changed even since the 2016 video...I thinned it out a bit. Down to 75 now.

Greg V.
West Bend, WI
Member WARCI.org




Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Made mistake & did not label connection
Hi John, I don't have this radio, but I can supply some info: Based on your pic, pins 7,8 and 1 are used together, go...MrFixr55 — 02:02 PM
New Philco Repair Bench
As far as I know, the Repairbench does not work, and has not been working in a while. Chuck (we had that campaign looki...morzh — 01:33 PM
Radio city products 664 schematic request
Need a schematic or manual for the 664. The 663 may be similar.daveone23 — 12:38 PM
New Philco Repair Bench
Thanks Gary.dconant — 12:16 PM
New Philco Repair Bench
I tried accessing the site through our library and got the same response. It's reported to our tech gurus. GaryGarySP — 11:50 AM
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM

[-]
Who's Online
There are currently 5707 online users. [Complete List]
» 2 Member(s) | 5705 Guest(s)
AvatarAvatar

>