1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Test Equipment
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
B&K 600 tube tester restoration
madrescuer
New Member
*
Posts: 1
Threads: 1
Joined: Jul 2016
City: Howell,NJ
#1

10-18-2016, 08:16 PM
I was recapping the Tube tester and was having some difficulty finding a 5uf 250v electrolytic capacitor. I have a 8uf 450 volt electrolytic.Is this an acceptable substitute?
Thanks in advance!
Find
morzh
Odobenus rosmarus
*****
Posts: 15,818
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#2

10-19-2016, 07:52 AM
It depends where it is in the circuit.

http://www.mouser.com/ProductDetail/Corn...X1Hdo6Q%3d

http://www.mouser.com/ProductDetail/Corn...BvZ%2fE%3d
(might be OK, depends where in circuit)

http://www.mouser.com/ProductDetail/Pana...rFOO8a4%3d

etc.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
Kenneth F. Besso Jr.
Senior Member
****
Posts: 667
Threads: 11
Joined: Sep 2014
City: Bellmawr, NJ
#3

10-19-2016, 06:51 PM
HOW about ,,JUSTRADIO,,,,,CANADA
Find
Phlogiston
Radio-Fixer-Upper
*****
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
#4

10-25-2016, 12:21 PM
If it really is 8uf (test it) then it will probably be fine. The tolerance on the old electrolytics was something like -30% to +80%.
Most of the high-compliance parts in old testers are marked. If it is one of these marked parts find a close match.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
(This post was last modified: 10-25-2016, 12:23 PM by Phlogiston.)
Website Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM

[-]
Who's Online
There are currently 7048 online users. [Complete List]
» 2 Member(s) | 7046 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Test Equipment