Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 16B restoration
#1

 With the weather cooperating I decided to get this one finished. Its been sitting in the basement for 2 years.
The damage was there when I got it.
[Image: http://i1336.photobucket.com/albums/o654...rnpbcq.jpg]

[Image: http://i1336.photobucket.com/albums/o654...rc79r9.jpg]

 After stripping.
[Image: http://i1336.photobucket.com/albums/o654...fv0yer.jpg]

 This is after some toner and 3 coats lacquer. It was darker than the picture but still not right.
[Image: http://i1336.photobucket.com/albums/o654...r5u3pk.jpg]

 I had to order more extra dark walnut I had ran out. Little better now.
[Image: http://i1336.photobucket.com/albums/o654...32y9hb.jpg]

  After decal and 4 more coats lacquer. Don't know if I should just wait a few weeks and rub it out and polish or sand it again and apply more lacquer. Looks pretty good as is.

[Image: http://i1336.photobucket.com/albums/o654...4dknnq.jpg]
  I still have to paint the stripes on the front.

[Image: http://i1336.photobucket.com/albums/o654...6ealcy.jpg]
#2

Very nice! Icon_thumbup

Just went through the same process in September on my model 16:

   

   

Greg V.
West Bend, WI
Member WARCI.org
#3

  Very good looking Greg. Icon_thumbup  These big cabinets are a lot of work , but I do enjoy it.  If I may ask ... what did you use to paint the ivory colored stripes with?
#4

Thanks Mike. I actually used Testors gloss white and a microbrush to paint the stripes. Carefully masking the area around the stripes off using Scotch 3M 1/4 wide plastic tape. The Testors model paint 'flows' nicely in the grooves for the stripes with the microbrush.

   

Greg V.
West Bend, WI
Member WARCI.org
#5

Thank you, I will give that a try.
#6

Beautiful!
Both of you...

I will get to mine in the spring Icon_rolleyes

Me

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#7

WOW,,very very nice job
#8

Very dashing!

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#9

Beautiful job!
#10

Beautiful job on the radio indeed..Give yourself a hand!   Icon_clap Icon_clap Icon_clap
#11

Icon_thumbup Icon_thumbup Icon_thumbup
#12

Thanks guys. Just waiting on some grill cloth and should get it completed.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 5057 online users. [Complete List]
» 1 Member(s) | 5056 Guest(s)
Avatar

>