Thread Rating:
  • 1 Vote(s) - 2 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Today's finds
#1

Today's finds. We are visiting the in-laws in Iowa City. Went to a farm house in Iowa to purchase a 46-350 that I found on Craigslist. Came home with that AND a Silvertone 7104 farm radio. Total of $40. The Silvertone uses a 2 volt "A" battery and a 90 volt "B" battery. I am looking for the cheapest solution to get this up and running. Ideas?



Thanks,
TerryMSU


Attached Files Image(s)
       
#2

Nice finds! The B battery is easy... 10 9volt batteries in series will work. As for the A battery, 2 1.5 volt batteries in series and calculate a resistor to bring them down to 2 volts perhaps? I'm sure other will chime in with possibilities for you. Take care, Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#3

I have a lab power supply for the filaments, so that is the easy part.

Thanks,
TerryMSU
#4

 If the Silvertone does use 2 volt filament battery tubes and not 1.5 volt ones, not many sets used 2 volt tubes after 1938. The B+ supply is usually easy if it's only 90 volts, you can make a supply similar to what the 46-350 uses with a three section pi filter arrangement.
Regards
Arran
#5

There are so many nice schematics for building a 90/1.5 powersupply. I'm certain with a few mods it could handle 2V. I have built three into a case with graphics to look pretty stock. I just didn't wish to replace batteries! Yes, it does have an A/C cord coming out.
Jerry

Here is a picture of a 90V/1.5V powersupply built into a nice box with graphics to run a farm radio.

[Image: http://i303.photobucket.com/albums/nn129...Radio2.jpg]

A friend in need is a pest!  Bill Slee ca 1970.
#6

(11-25-2016, 10:12 PM)jerryhawthorne Wrote:  There are so many nice schematics for building a 90/1.5 powersupply. I'm certain with a few mods it could handle 2V. I have built three into a case with graphics to look pretty stock. I just didn't wish to replace batteries! Yes, it does have an A/C cord coming out.
Jerry

Here is a picture of a 90V/1.5V powersupply built into a nice box with graphics to run a farm radio.

[Image: http://i303.photobucket.com/albums/nn129...Radio2.jpg]

It looks like this is a 1.5 volt filament radio. Any recommendations for battery replacement circuitry that anyone has used? I have the background to tweak any design that shows up, but a proven design may help me to find just the right parts.

Thanks,
TerryMSU




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Model 96 cabinet veneer
There is some description of the veneers in the 1930 Brochure in our library. Here's the link: klondike98 — 11:59 PM
Philco 91 Speaker Replacement
I can't remember, but there was a particular product for loosening glue on the more modern "spiders", used pos...MrFixr55 — 09:43 PM
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM

[-]
Who's Online
There are currently 1118 online users. [Complete List]
» 2 Member(s) | 1116 Guest(s)
AvatarAvatar

>