Giid leak voltage on Sears 101.557-1 chassis
Posts: 85
Threads: 13
Joined: Jul 2015
City: Rockville, MD
Hi all. Been working on this for a while off and on. Re-capped, re-resistored, aligned(at least I think it's right). Now I get one strong station at 1600kc, but the oscillator seems to drop out as I dial toward the lower end of the dial. Grid leak voltage on the LO drops to almost nothing at that point. Why would the tuning cap cause this voltage to drop? All suggestions gratefully accepted. Thanks, Ed
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
Hi Ed,
So your under winx's tower???
Check voltage on pin's 3 and 4 of the mixer tube if you have the 140v or so replace the 6J8. This is assuming that set has been serviced, tube sockets and tuning cap have been cleaned, and check for bent plates. Also check C-6 for proper tracking at the low end of the bc band, could be that it's adjusted so that it is out of the range of the oscillator ability to oscillate (too low).
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
(This post was last modified: 11-28-2016, 08:51 PM by Radioroslyn.)
Posts: 85
Threads: 13
Joined: Jul 2015
City: Rockville, MD
(11-28-2016, 08:22 PM)Radioroslyn Wrote: Hi Ed,
So your under winx's tower???
Check voltage on pin's 3 and 4 of the mixer tube if you have the 140v or so replace the 6J8. This is assuming that set has been serviced, tube sockets and tuning cap have been cleaned, and check for bent plates. Also check C-6 for proper tracking at the low end of the bc band, could be that it's adjusted so that it is out of the range of the oscillator ability to oscillate (too low).
Terry
Ha Ha, yeah Terry you could say that. About a mile as the proverbial crow flies, near the Burgundy strip mall. Sadly WINX has gone the way of almost all the old AM rock stations. Now it's hispanic, and I can't remember what the call sign is. Only one tower now instead of the 3 or 4 that used to be off of 355 back in the day. It comes in loud and clear no matter what. Anyway, changed 6j8, no help, 140v on mixer, -6v at osc grid which drops to .113 or so at about 6 or 700kc. Adjusted padder c-6. Passes signal weakly at 600kc, but no stations. I think I'm gonna go cry in my beer now. Thanks for the response Terry. Really appreciate the help all you guys offer here. Ed
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
You probably know this but I'll mention it in passing R-1 is listed as a 40M resistor. That = 40,000 or 40K ohms not 40 megohm. Check your ground connections at the coil. Rivets are always suspect.
Was down in ur hood for tday in Gsburg.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
(This post was last modified: 11-28-2016, 10:41 PM by Radioroslyn.)
Posts: 85
Threads: 13
Joined: Jul 2015
City: Rockville, MD
(11-28-2016, 10:39 PM)Radioroslyn Wrote: You probably know this but I'll mention it in passing R-1 is listed as a 40M resistor. That = 40,000 or 40K ohms not 40 megohm. Check your ground connections at the coil. Rivets are always suspect.
Was down in ur hood for tday in Gsburg.
Yeah, I replaced R1 with a new 39k I had. Was reading about 2500 over. Meant to mention that in the last post. Did you get to Rockville while you were down? How far is it from where you live? I'll check the grounds next time I'm poking around in there. Didn't think of that. Thanks for the heads up on that. Ed
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
Did you get to Rockville while you were down?
nah did quite down to Harvard on the Pike (a euphemism from my misspent youth)
How far is it from where you live?
Abt 3hrs north.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 85
Threads: 13
Joined: Jul 2015
City: Rockville, MD
Well, checking grounds around the coils and trimmers, they all seem good. Wonder if I could have a bum replacement tube in there. Still don't know why the grid leak voltage drops out when I turn the tuning cap to the low end of the dial. The oscillator can't be running with no bias can it? I also seem to remember reading that the 6j8 can be a finicky oscillator, but there doesn't seem to be any alternate replacement for it. The one in there is one I ordered as nos. Don't know where to go from here. Maybe try re-aligning it. Ed
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
I like easy questions.
> Still don't know why the grid leak voltage drops out when I turn the tuning cap to the low end of the dial.
Because there isn't enough feedback to keep the osc running. This can be caused the tube not having enough gain (weak or voltages too low), Bad coil, or out of tolerance micas/ tuning cap shorted. Just for grins check the heater voltage on the 6J8 (needs to be 6.0vac or more).
> The oscillator can't be running with no bias can it?
The control grid needs or will be negative when it is oscillating. Not oscillating the grid will be at 0 or positive using a high Z meter, no VOM.
For a drop in replacement try a 12A8. None the the 6J8's 6v friends have a 150ma heater there all 300ma. Electrically the 6A8/12A8 has more gain than the 'J8 which is good.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
(This post was last modified: 11-29-2016, 05:17 PM by Radioroslyn.)
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
Sorry misread the specs, use 6A8. All the other tube have a 300ma heaters.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 85
Threads: 13
Joined: Jul 2015
City: Rockville, MD
Have to dig through my tubes to see if I have one. Meanwhile there is a cap on pin 4 of the 6u7 that doesn't look like it belongs there. Other end goes to ground. could this be a problem?
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
(11-30-2016, 01:14 PM)leftwing25 Wrote: Have to dig through my tubes to see if I have one. Meanwhile there is a cap on pin 4 of the 6u7 that doesn't look like it belongs there. Other end goes to ground. could this be a problem?
Don't think so. Just bypasses the SG and SG of the 6J8.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 85
Threads: 13
Joined: Jul 2015
City: Rockville, MD
Ok, so tried another 6j8 I found, same results. Just noticed that I replaced R-8 with a .1mfd instead of the .22 I had intended to use. Would that affect anything badly?
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
Methinks you mean C-8, possible maybe may alter the cathode voltage a bit. also check R-2.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 85
Threads: 13
Joined: Jul 2015
City: Rockville, MD
(11-30-2016, 08:46 PM)Radioroslyn Wrote: Methinks you mean C-8, possible maybe may alter the cathode voltage a bit. also check R-2.
Yeah, kinda thought that might be the case. Yep, c-8. Resistors don't use mfds. Also noticed B+ is about 14 volts low at the rectifier cathode, but plate voltages only about 5 volts low, i.e., 140 reading 135-138. Possible problem? Unfortunately don't have any 25z6's to replace it with. Anyway, will replace c-8 and see what happens. Thanks, Terry. Ed
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
(12-01-2016, 05:45 PM)leftwing25 Wrote: (11-30-2016, 08:46 PM)Radioroslyn Wrote: Methinks you mean C-8, possible maybe may alter the cathode voltage a bit. also check R-2.
Yeah, kinda thought that might be the case. Yep, c-8. Resistors don't use mfds. Also noticed B+ is about 14 volts low at the rectifier cathode, but plate voltages only about 5 volts low, i.e., 140 reading 135-138. Possible problem? Unfortunately don't have any 25z6's to replace it with. Anyway, will replace c-8 and see what happens. Thanks, Terry. Ed
Doubt 5v is going to make much of a difference.
If you like excitement you tie a couple of 1N4007 across your 25Z6. Did I say that??? [Image: http://philcoradio.com/phorum/images/smi...on_eek.gif] That will get ur 140 up the abt 160. On second thought probably not a good idea. This set uses a voltage doubler where the DC output should be much higher than 140v. Typical doubler would have an output of abr 250vdc w/120ac input. Not quite sure how they get the power supply to work with such low output.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
(This post was last modified: 12-01-2016, 06:15 PM by Radioroslyn.)
Users browsing this thread: 1 Guest(s)
|
Recent Posts
|
Cannot Adjust an IF Transformer’s cores
|
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM |
Cannot Adjust an IF Transformer’s cores
|
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM |
PT-6 antenna connections
|
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM |
Cannot Adjust an IF Transformer’s cores
|
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM |
PT-6 antenna connections
|
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4.
Yes, pin 6 of the 7C6 is...RodB — 07:34 PM |
bridkarl
|
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM |
Cannot Adjust an IF Transformer’s cores
|
Joseph, now you are an engineer!!RodB — 06:37 PM |
PT-6 antenna connections
|
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM |
Cannot Adjust an IF Transformer’s cores
|
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM |
PT-6 antenna connections
|
I seem to have lost my way on this PT-6.
I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM |
Who's Online
|
There are currently 4193 online users. [Complete List] » 1 Member(s) | 4192 Guest(s)
|
|
|
![>](https://philcoradio.com/phorum/images/bootbb/asb/right_arrow.png)
|