1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
42-365
sam
Phorum Expert
*****
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
#61

12-08-2016, 08:23 PM
lol Icon_lol
I like how you phrased that

Now you know that's not the right answer!!!!!

sam
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Find
ccbaker13
Member
***
Posts: 65
Threads: 4
Joined: Oct 2016
City: Alexandria Virginia
#62

12-08-2016, 09:28 PM
I think 0.6 Ohm is what it should be
Find
ccbaker13
Member
***
Posts: 65
Threads: 4
Joined: Oct 2016
City: Alexandria Virginia
#63

12-08-2016, 09:28 PM
Or "less 1 ohm" ?
Find
ccbaker13
Member
***
Posts: 65
Threads: 4
Joined: Oct 2016
City: Alexandria Virginia
#64

12-08-2016, 09:30 PM
Or is it "less 0.1 ohm"
Find
morzh
Odobenus rosmarus
*****
Posts: 15,825
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#65

12-08-2016, 09:37 PM
I think Sam is referring to the missing punctuantion after "powered off" Icon_smile
Truthfully, took me a while to understand it too Icon_lol

"EXECUTE NOT PARDON". Which one is it? Icon_lol
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
ccbaker13
Member
***
Posts: 65
Threads: 4
Joined: Oct 2016
City: Alexandria Virginia
#66

12-08-2016, 09:55 PM
I think there is a disconnect. I was just saying the the resistance from pin 7 was measured to be 0.6 Ohms with the radio powered off. Then I was following the line from the pin on the schematic and was thinking that the resistance is written as "less 1 ohm" or possibly it says "less 0.1 Ohm" there.
But I did have a laugh at "Now you know that's not right"
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#67

12-08-2016, 10:08 PM
Still not the right answer!
I was looking for something open.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 12-08-2016, 10:18 PM by Radioroslyn.)
Find
ccbaker13
Member
***
Posts: 65
Threads: 4
Joined: Oct 2016
City: Alexandria Virginia
#68

12-08-2016, 10:17 PM
Ha! Ok what's the right answer? That tube should be 70V but its low. We tried disconnecting one end of 17 a week ago but that didn't raise the voltage.
Find
ccbaker13
Member
***
Posts: 65
Threads: 4
Joined: Oct 2016
City: Alexandria Virginia
#69

12-08-2016, 10:19 PM
Ok I'll look for something open
Find
ccbaker13
Member
***
Posts: 65
Threads: 4
Joined: Oct 2016
City: Alexandria Virginia
#70

12-08-2016, 10:23 PM
Well there isn't anything that isn't supposed to be
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#71

12-08-2016, 10:29 PM
(12-08-2016, 10:23 PM)ccbaker13 Wrote:  Well there isn't anything that isn't supposed to be

Well as Peavey the druggist would "I wouldn't say that"! The voltages aren't.
Does #27 measure 4.7K? and what are the voltages on both sides of it.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 12-08-2016, 10:35 PM by Radioroslyn.)
Find
ccbaker13
Member
***
Posts: 65
Threads: 4
Joined: Oct 2016
City: Alexandria Virginia
#72

12-08-2016, 10:57 PM
I get 4.7K and 10 volts across it
Find
ccbaker13
Member
***
Posts: 65
Threads: 4
Joined: Oct 2016
City: Alexandria Virginia
#73

12-08-2016, 10:59 PM
Oh sorry, 190V and 200V
Find
morzh
Odobenus rosmarus
*****
Posts: 15,825
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#74

12-08-2016, 11:05 PM
Reminds me of chess playing Icon_lol
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
ccbaker13
Member
***
Posts: 65
Threads: 4
Joined: Oct 2016
City: Alexandria Virginia
#75

12-08-2016, 11:12 PM
Yeah this radio is Bobby Fischer
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM

[-]
Who's Online
There are currently 2630 online users. [Complete List]
» 1 Member(s) | 2629 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration