1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Zenith 6S229 Tombstone
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#1

12-09-2016, 08:27 PM
I have a question about The Resistance readings on the following>>>

Power Transformer
Antenna Coil
Osc Coil
Output Transformer
IF Cans

My schematic has NO values for any of these..

Or does anyone have a different schematic with values on it...

Skip...
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,296
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

12-09-2016, 09:26 PM
>Power Transformer  The highest resistance will across the HV winding(around 200-400ohms or so) next the 120v primary (10-30ohm) the the heater windings (just a few ohms)

Antenna Coil Pri pretty low 2-6ohms  secondary pretty low also about the same.
Osc Coil Same as ant coil
Output Transformer primary 200-500 ohms secondary low a few ohms

IF Cans about 10-30ohms.

Mostly when you are checking the resistance of these items you are looking for a very high resistance indicating that the winding is open.
Generally with coils the lower the frequency the higher the resistance because it take more wire to make more inductance.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#3

12-09-2016, 10:54 PM
Terry, OK great That makes perfect since..

See you on Sun..

Skip...
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#4

12-12-2016, 01:18 AM
OK,, Here are some pictures>>

[Image: http://i292.photobucket.com/albums/mm38/...je2v1r.jpg]

Dial Looks good...

[Image: http://i292.photobucket.com/albums/mm38/...oqcelr.jpg]

Bottom of Cabinet Not so Good...

[Image: http://i292.photobucket.com/albums/mm38/...iagumv.jpg]


Oh goody.. More Mouse Drops??

[Image: http://i292.photobucket.com/albums/mm38/...gsbnjn.jpg]

Top Pretty rusty.. Its a copper Chassis..

[Image: http://i292.photobucket.com/albums/mm38/...gslqgo.jpg]

Under Chassis after Mouse removals..

Not to bad.. Next on to checking out Transformer and coils..

Anyone know what to use for this belt?? Its for the tuning..

[Image: http://i292.photobucket.com/albums/mm38/...xmenrr.jpg]

Skip...
Find
Dan Walker
Senior Member
****
Posts: 376
Threads: 105
Joined: Jul 2011
City: Calgary, AB, CA
#5

12-12-2016, 11:56 AM
http://www.adamsradio.com/page1.html

 Here is where you can get the belt you need.
   It looks like you have your work cut out on this one, but it should turn out good .
 Dan in Calgary
 
   Living in Calgary Alberta
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#6

12-13-2016, 01:04 AM
Ok, Update: The Transformer, Antenna Coil, Osc Coil and IF cans all have Continuity.. Nothing Open..

So now waiting on a Price ..

Can someone please tell me approx what to offer for this..I do not want to Low ball but also do not want to over pay...

This is from the ( Pickers house) That I had set aside. I liked the looks and cabinet wasn't Bad..

Help Please

Thanks
Skip...
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#7

12-13-2016, 09:05 PM
Couple of more questions:...

There are 3 extra Variable Trimmer caps in bottom of radio that I cannot ID Circled in RED..
Any Clue What they are for?

[Image: http://i292.photobucket.com/albums/mm38/...45xtjp.jpg]

Here is alignment Instructions

[Image: http://i292.photobucket.com/albums/mm38/...ynksrw.jpg]

[Image: http://i292.photobucket.com/albums/mm38/...ztqf4g.jpg]


Also is this Factory??

[Image: http://i292.photobucket.com/albums/mm38/...whd30b.jpg]

Skip...
Find
Eliot Ness
Phorum Expert
*****
Posts: 3,148
Threads: 56
Joined: Apr 2011
City: Lexington, KY
#8

12-17-2016, 06:32 PM
(12-13-2016, 01:04 AM)vecher Wrote:  ......So now waiting on a Price ..

Can someone please tell me approx what to offer for this..I do not want to Low ball but also do not want to over pay...

Need to see a picture of the cabinet and how many of the Zenith wood knobs does it have? 

The 6-S-229 has a photo finish so condition plays into the value:

http://www.radiophile.com/6s229.htm
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#9

12-17-2016, 06:59 PM
Ok, I will take picture.. It has 3 of the 4 Knobs Missing 1 knob..

Skip...
Find
morzh
Odobenus rosmarus
******
Posts: 16,481
Threads: 573
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#10

12-17-2016, 07:57 PM
Skip

To be perfectly honest I never care about exact resistance reading of coils. If the coil is original and not open, it is OK and this is a fact. And you can tell open (infinite ohms)or leakage (hundreds of K to Megs to Gigs) from real resistance (units to tens of Ohms in RF coils, hundreds ohms in output xfmr primaries etc). And ohmmeter will not tell you about turn shorts.

So it is a waste of time to try to find out exact numbers. See if it is open. If not, it is presumed good. Rare cases of leakages and turn shorts are diagnosed by symptoms.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#11

12-17-2016, 08:46 PM
Ok,Thanks all.. Here are pictures of Cabinet..

[Image: http://i292.photobucket.com/albums/mm38/...iwicec.jpg]

[Image: http://i292.photobucket.com/albums/mm38/...abrrk4.jpg]

[Image: http://i292.photobucket.com/albums/mm38/...gxejhk.jpg]

[Image: http://i292.photobucket.com/albums/mm38/...nx5pft.jpg]

Skip...
Find
OldRestorer
Electronic geneus
*****
Posts: 4,106
Threads: 310
Joined: Nov 2013
City: Kings Park NY
#12

12-17-2016, 09:34 PM
Hey,
The Photofinish looks good to me.. I would just clean up the cabinet personally.
If you want it better then strip the top only and refinish it...
DO NOT touch the photofinish...
Black magic marker will fix the trim issues...
I know you dont do cabinets (yet) but this is an easy one....

I think $75.00 max.. Probably $50.00...

Me
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
morzh
Odobenus rosmarus
******
Posts: 16,481
Threads: 573
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#13

12-17-2016, 10:12 PM
Easy for you to say. If I were shocked 60 times, I'd say the same. Icon_lol
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#14

12-19-2016, 12:08 AM
Have another question... How do you clean the dial? It seems to have spots .. I think when cleaning the pots some cleaner might have gotten on it.. I do not remember seeing them there before..

[Image: http://i292.photobucket.com/albums/mm38/...0nphbv.jpg]

Waiting on parts and belts .. Should be here this week .. Then start recap..

Thanks...

Skip
Find
morzh
Odobenus rosmarus
******
Posts: 16,481
Threads: 573
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#15

12-19-2016, 09:09 AM
Find an inconspicuous spot, try mineral spirits.
If it works, you could do the rest.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Zenith H725
Here's what the inside of AM IFT2 looked like, and the other pic shows the discs I made to take place of the mica and ke...EdHolland — 07:40 PM
Zenith H725
IF2 will need replacement caps. The arcing was severe enough that the mica is pitted and holed where the HT flashed over...EdHolland — 04:04 PM
My Philco 37-116 Restore
Measuring from center tap like the tube voltages show. Cap 127 is isolated from ground. Cap 127 shown in upper left of p...dconant — 08:05 AM
My Philco 37-116 Restore
Are you measuring relative to the centertap or the GND?morzh — 11:57 PM
Philco 610B oscillator wiring
Still not clear on the wiring interface between the 6A7 and oscillator. After refering to the available schematics and s...Tubester — 07:18 PM
Refinishing Ideas
My 37-116 code 121 is the best sounding radio i have...a daily driver. Since we are talking about "changes". ...poulsbobill — 07:18 PM
My Philco 37-116 Restore
Hello, I finally got brave enough to take the cans off the Expander Unit. Got the grid cap wires replaced and back toget...dconant — 06:50 PM
Zenith H725
I got into the first AM IF can today, and found its mica was cracked. Amazing that it was still working. This one makes ...EdHolland — 06:10 PM
Philco model #20
AHH HA , I got it and can’t thank you fellows enough , when I changed the capacitors I took the advice and did not unsol...onlyrick — 02:24 PM
Zenith H725
Hello Ed, yes, I like letting projects run for few days to make sure they don't start acting up . Sincerely Richardradiorich — 01:03 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)