Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

40-185 Tuning Oddities
#1

I recently bought a nicely preserved 40-185 which promptly started right up after finding a missing 7C6 tube. The tuning seems a bit funny and I'm at a bit of a loss as to why. This model has a dial as well as pre set push buttons, all of which work well. It also has 3 bands, AM, SW, and Police. If I nutralize the push buttons, I'm assuming that the dial then becomes active. However, when the knob is turned, all I hear is the typical buzzing from power lines etc (not confused with the capacitor's humming if they are bad) and no stations. If I use the presets, the 1st 2 buttons give a few local channels loud and clear. The tuner turns freely and touching the antenna connections changes the level/loudness of the AM static, but no stations. Could someone explain how the presets work VS the dial tuner, and hopefully why the presets work but the tuner doesn't.
Any and all help is appreciated!

Jim
#2

One of the pushbuttons selects MANUAL TUNING and if it's not pushed in, you'll get nothing. I believe it's the far right pushbutton, if I'm not mistaken.

On most pushbutton type radios, there will always be a MANUAL selection, although there may be rare exceptions I'm not familiar with.
#3

Thanks for the help...it worked! I read (in another thread) about dirty contacts causing issues as well so pushing the rightmost butto and wiggling it a bit allowed the other stations to come in loud and clear...I have to admit i was surprised. I appears that someone recapped the unit at some point and now it works quite well, at leat on AM. The other 2 bands are unknown since they are typically quiet during the day, but I didn't hear much static either.
I guess one task at a time is best.....

Thanks again,

Jim
#4

Hi Jim

You need to clean the contacts on all of the pushbuttons, as well as the contacts on the band switch. Deoxit is great for this. I tried CRC QD Contact Cleaner on my 40-155 (nearly identical chassis to your set) and it didn't work; the band switch and pushbuttons remained intermittent. After a dose of Deoxit, though, everything is fine; all pushbuttons now work as intended as does the band switch. All three bands are alive and work fine.

These are actually pretty good performers; they get their bad reputation from the rubber insulation used on the wires. Once you replace the old rubber as well as all of the paper capacitors and off-tolerance resistors, though, you have a really good, sensitive radio.

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 3492 online users. [Complete List]
» 2 Member(s) | 3490 Guest(s)
AvatarAvatar

>