Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 37-610
#1

Hi,

Some time ago a relative found me a Philco bullet model 37-610 at a sale. Upon inspecting it later, I noted that it did not have the Deco inlaid lines on the front:- http://www.tuberadioland.com/philco-37-6...mainl.html

It's also missing its dial glass and part of the knob, though I do have these parts that I've found since.

I've seen very few of these without the lines & have been uncertain as to their authenticity. Now one has shown up on Ebay:-
http://cgi.ebay.com/6596526279

Is there a story here somewhere regarding this as a variation?

Paul
#2

Looked at the ebay set. It's glaringly a strip 'n slobber refinish. I don't believe that these models ever had Di-Noc (printed grain) finishes, but we have to wonder if the black stripes may have been printed on the panels. I'll have to check on mine, but I've always thought that the black stripes were inlays. I have both the '36 and the '37 sets.

Another possibility is that on early cabinets, the stripes WERE inlays, and they might have done a run of cabinets with either printed stripes or none at all. Since the original finish is gone from this cabinet, that information is lost.
#3

I think I would have to agree with Doug here. Although that decal looks as if it might be original, the bottom trim should be toned a much darker brown; and it isn't on this set.

Some years ago, someone was selling a very good reproduction of the 1932-36 PHILCO decal. I once had a few of those, and they looked just like the originals, unlike what you can get today. The decal on this set could be one of those repros, placed on an older, poor refinish, for all we know.

I looked in my copy of Furniture History, and it is silent on the stripes/no stripes issue. It only mentions that the 1937 version was available in maple as well as walnut; the vast majority (28,100) were walnut as opposed to 3,000 in maple.

I wouldn't be a bit surprised if Doug is right on the money regarding the stripes being printed later on, although I seem to recall the 1936 model did have inlaid stripes?

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently 5583 online users. [Complete List]
» 3 Member(s) | 5580 Guest(s)
AvatarAvatarAvatar

>