1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Audio driver transformer
AB1VL
New Member
*
Posts: 1
Threads: 1
Joined: Mar 2017
City: Searsport, ME 04974
#1

03-26-2017, 04:02 PM
Just registered. I picked up a Philco shelf xcvr carcass of unknown model and date at a hamfest. It has a serial number tag D 09758.  No power xformer so I'm guessing it's an AC/DC rig.

I'm interested in getting specs for what I think is an audio transformer part number 32-8179N. It has at least one wire left that goes to the voice coil winding of an oval speaker.  Tube complement is 1 XXD, 1 7C6, 1 50L6 GT, 1 35Z5, 4 x 7b7 loctal base tubes.   I got it for a buck as a parts donor, and now I need a low power audio xformer for a breadboard project. 

I'm not interested in a restoration so if any of you want parts from it RSVP. I have some remains of the wood cabinet but it's pretty rough.  tnx in advance, chuck
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,297
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

03-26-2017, 05:54 PM
Hi Chuck and welcome,
It would be considered an audio output transformer. Pri 2K @ 40ma Sec 4 ohms.

GLOM
Terry N3GTE
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 03-26-2017, 05:55 PM by Radioroslyn.)
Find
klondike98
Phorum Moderator
******
Posts: 5,163
Threads: 273
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#3

03-26-2017, 06:42 PM
Welcome to the Phorum!
Icon_wave
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Refinishing Ideas
Hi Poulsbobl, I think that you could get away with it.  In the Philco Library, there is a parts listand specs for sp...MrFixr55 — 11:54 PM
Philco 46-480 Electronic Restoration
The sleeving for the transformer arrived early, so I went ahead and finished reassembling. The chassis looks far better ...jrblasde — 10:15 PM
Philco 610B oscillator wiring
I don't know what you are referring to when you say "tube cathode ground". Ground is a connection to the chass...RodB — 05:56 PM
Zenith H725
Good points, Arran. I haven't encountered this problem with any other radio (all earlier vintages), so am learning here....EdHolland — 05:32 PM
Zenith H725
Ed; One thing that I will say about these is that Brand Z was considerate enough to make these mica caps easily acces...Arran — 02:34 PM
Philco 610B oscillator wiring
Do you know what run # your chassis is? It took me a while to find what you were basing updates/modification on as I did...Radioroslyn — 07:34 AM
Need to purchase some accessories for restoration of my Old Philco Radio
COLLEAGUES, Thank you all for such good and important suggestions as how to find good replacement parts. I will go fo...palonso — 07:05 AM
Zenith H725
Here's what the inside of AM IFT2 looked like, and the other pic shows the discs I made to take place of the mica and ke...EdHolland — 07:40 PM
Zenith H725
IF2 will need replacement caps. The arcing was severe enough that the mica is pitted and holed where the HT flashed over...EdHolland — 04:04 PM
My Philco 37-116 Restore
Measuring from center tap like the tube voltages show. Cap 127 is isolated from ground. Cap 127 shown in upper left of p...dconant — 08:05 AM

[-]
Who's Online
There are currently 560 online users. [Complete List]
» 2 Member(s) | 558 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration