1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
38-12 Dial Face Removal
Winky Dink
Member
***
Posts: 122
Threads: 22
Joined: Dec 2013
City: Meridian, ID
#1

04-13-2017, 01:13 PM
Is there any way to remove the pointer so that I can remove the cardboard dial face before I start cleaning the chassis?

[Image: https://c1.staticflickr.com/4/3933/34016...2bc7_z.jpg]

Thanks,
Henry.
Find
KCMike
Phorum Expert
*****
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
#2

04-13-2017, 01:49 PM
I restored one quite awhile back. I think that dial pointer just pulls off. Not easily, be careful with it.
Find
morzh
Odobenus rosmarus
*****
Posts: 15,527
Threads: 545
Joined: Oct 2011
City: Jackson, NJ
#3

04-13-2017, 03:16 PM
It pulls out, pretty simply. Pull the pointer by the hub, not by the hand, use your fingernails to pull it. be gentle, not much effort is needed.
When using your nails, make sure you feel the pressure your joints exert onto the dial face to be very light - it is easily smushed.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 04-13-2017, 03:17 PM by morzh.)
Find
Winky Dink
Member
***
Posts: 122
Threads: 22
Joined: Dec 2013
City: Meridian, ID
#4

04-13-2017, 03:47 PM
Thanks. I hadn't found the edge of the hub, but I have exactly the right tool and I'll get to it tonight.
Find
Winky Dink
Member
***
Posts: 122
Threads: 22
Joined: Dec 2013
City: Meridian, ID
#5

04-14-2017, 01:13 AM
This is why I couldn't find the hub.  I held the rotor still and gave a little twist to the pointer.  Then it slid off easily.

[Image: https://c1.staticflickr.com/3/2886/33984...0850_n.jpg]
Thanks again.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Correct model 84 Ac plug an cord type
From what I read Philco went to using brown rubber power cords in 1936, so cloth was used in the 1935 and earlier models...Arran — 11:25 PM
Correct model 84 Ac plug an cord type
Hi Bruce, I have not worked on an 84, but in general, power cords for almost any radio prior to 1938 was cloth covered...MrFixr55 — 08:34 PM
Restoring Philco 38-14
OK, well, so after staring at the sch again, I realized the problem had to be the #12/12A padder. I put a scope on the o...morzh — 08:15 PM
Correct model 84 Ac plug an cord type
Hello Bruce, I mostly use brown far as my cloth powercords go ! Here is the plug that I have used bakelite Acorn style...radiorich — 08:05 PM
Correct model 84 Ac plug an cord type
Looking for as correct as can find the right Ac plug an the correct colored cloth line. Ive seen many old photos but mos...Bruce — 04:13 PM
Restoring Philco 38-14
Rod Two Y-caps make sense if you use them from L/N to the chassis; this is only makes sense in the transformer radios...morzh — 10:11 AM
Restoring Philco 38-14
Mike, I'm curious about a specific use of he Y cap. Lately I've seen a single cap across the power transformer primary. ...RodB — 09:01 AM
Restoring Philco 38-14
hello morzh , That sounds like a plan ! Sincerely Richardradiorich — 07:45 AM
Restoring Philco 38-14
Richard, It helped some, but I still had the whining when engaging the rear power strip (I did not realize it was fro...morzh — 07:07 AM
Restoring Philco 38-14
Hello morzh, Yes , that dreaded hum in my room where i do alighment I have my cable modem and router plus desktop plus ...radiorich — 11:25 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration